176 lines
4.7 KiB
INI
176 lines
4.7 KiB
INI
[include fluidd.cfg]
|
|
|
|
[virtual_sdcard]
|
|
path: /home/pi/printer_data/gcodes
|
|
on_error_gcode: CANCEL_PRINT
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 2
|
|
max_z_accel: 100
|
|
|
|
[stepper_x]
|
|
step_pin: PE3
|
|
dir_pin: !PE2
|
|
enable_pin: !PE4
|
|
microsteps: 16
|
|
rotation_distance: 34.64
|
|
endstop_pin: ^PA15
|
|
position_endstop: 140
|
|
position_max: 150
|
|
position_min: -10
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PA10
|
|
interpolate: False
|
|
run_current: 0.4
|
|
|
|
[stepper_y]
|
|
step_pin: PE0
|
|
dir_pin: PB9
|
|
enable_pin: !PE1
|
|
microsteps: 16
|
|
rotation_distance: 34.64
|
|
endstop_pin: ^PA12
|
|
position_endstop: 0
|
|
position_max: 160
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PA9
|
|
interpolate: False
|
|
run_current: 0.4
|
|
|
|
[stepper_z]
|
|
step_pin: PB5
|
|
dir_pin: !PB4
|
|
microsteps: 16
|
|
rotation_distance: 0.586
|
|
enable_pin: !PB8
|
|
endstop_pin: probe:z_virtual_endstop #!PA11 is on board
|
|
position_max: 100
|
|
position_min: -5
|
|
homing_positive_dir: False
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC7
|
|
interpolate: False
|
|
run_current: 0.4
|
|
|
|
[extruder]
|
|
step_pin: PD6
|
|
dir_pin: !PD3
|
|
enable_pin: !PB3
|
|
microsteps: 16
|
|
rotation_distance: 16.1693
|
|
full_steps_per_rotation: 400
|
|
nozzle_diameter: 0.350
|
|
filament_diameter: 1.750
|
|
max_extrude_only_velocity: 2000
|
|
heater_pin: PC3
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC1
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 220
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PC13
|
|
interpolate: False
|
|
run_current: 0.4
|
|
#[extruder1]
|
|
#step_pin: PC1
|
|
#dir_pin: PC3
|
|
#enable_pin: !PC7
|
|
#heater_pin: PH6
|
|
#sensor_pin: PK7
|
|
#...
|
|
|
|
[heater_bed]
|
|
heater_pin: PA0
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC0
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[heater_fan heatbreak_cooling_fan]
|
|
pin: PB1
|
|
heater: extruder
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
restart_method: command
|
|
|
|
[force_move]
|
|
enable_force_move: true
|
|
|
|
[include eddy.cfg]
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 75,75
|
|
z_hop: 2
|
|
|
|
[screws_tilt_adjust]
|
|
#screw1=0,95+33 (eddy offset)
|
|
screw1=0,128
|
|
screw1_name=Left Screw
|
|
#screw2=135,57+33
|
|
screw2=135,90
|
|
screw2_name=Back Right Screw
|
|
#screw3=135,105
|
|
screw3=135,138
|
|
screw3_name=Front Right Screw
|
|
screw_thread: CW-M3
|
|
speed=60
|
|
horizontal_move_z=5
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [probe_eddy_current btt_eddy]
|
|
#*# reg_drive_current = 15
|
|
#*# calibrate =
|
|
#*# 0.049993:3223222.398,0.089914:3222696.923,0.130019:3222199.447,
|
|
#*# 0.169940:3221583.608,0.210044:3220854.994,0.249966:3220183.661,
|
|
#*# 0.290070:3219155.391,0.329991:3218089.993,0.369913:3217043.071,
|
|
#*# 0.410017:3215993.543,0.449938:3214994.125,0.490042:3214112.086,
|
|
#*# 0.529964:3213156.046,0.570068:3212314.775,0.609989:3211459.497,
|
|
#*# 0.649911:3210584.734,0.690015:3209689.801,0.729936:3208836.978,
|
|
#*# 0.770041:3208023.010,0.809962:3207289.863,0.850066:3206599.916,
|
|
#*# 0.889987:3205856.377,0.929909:3205162.218,0.970013:3204410.580,
|
|
#*# 1.009934:3203712.190,1.050039:3203027.201,1.089960:3202390.155,
|
|
#*# 1.130064:3201851.496,1.169986:3201312.538,1.210090:3200748.371,
|
|
#*# 1.250011:3200155.821,1.289932:3199526.630,1.330037:3198942.050,
|
|
#*# 1.369958:3198403.403,1.410062:3197912.325,1.449984:3197467.804,
|
|
#*# 1.490088:3196993.739,1.530009:3196530.609,1.569931:3196055.573,
|
|
#*# 1.610035:3195604.458,1.649956:3195164.639,1.690061:3194758.705,
|
|
#*# 1.729982:3194420.552,1.770086:3194061.651,1.810007:3193662.164,
|
|
#*# 1.849929:3193280.855,1.890033:3192880.718,1.929954:3192454.578,
|
|
#*# 1.970059:3192095.084,2.009980:3191755.446,2.050084:3191461.052,
|
|
#*# 2.090006:3191133.031,2.129927:3190756.179,2.170031:3190426.959,
|
|
#*# 2.209952:3190113.023,2.250057:3189810.939,2.289978:3189526.494,
|
|
#*# 2.330083:3189259.488,2.370004:3188972.679,2.409925:3188685.028,
|
|
#*# 2.450029:3188393.125,2.489951:3188135.144,2.530055:3187873.523,
|
|
#*# 2.569976:3187603.802,2.610081:3187382.983,2.650002:3187159.872,
|
|
#*# 2.689923:3186914.049,2.730028:3186656.198,2.769949:3186424.967,
|
|
#*# 2.810053:3186209.097,2.849974:3185999.953,2.890079:3185809.227,
|
|
#*# 2.930000:3185599.575,2.969921:3185419.073,3.010026:3185205.074,
|
|
#*# 3.049947:3184994.248,3.090051:3184782.938,3.129973:3184600.146,
|
|
#*# 3.170077:3184415.406,3.209998:3184252.974,3.249919:3184095.122,
|
|
#*# 3.290024:3183909.897,3.329945:3183742.613,3.370049:3183578.689,
|
|
#*# 3.409971:3183409.556,3.450075:3183260.146,3.489996:3183104.085,
|
|
#*# 3.529918:3182972.688,3.570022:3182810.155,3.609943:3182680.368,
|
|
#*# 3.650048:3182547.452,3.689969:3182392.135,3.730073:3182253.435,
|
|
#*# 3.769994:3182126.620,3.809916:3182014.604,3.850020:3181875.583,
|
|
#*# 3.889941:3181740.096,3.930046:3181596.221,3.969967:3181451.014,
|
|
#*# 4.010071:3181380.168,4.049993:3181262.890
|
|
#*#
|
|
#*# [temperature_probe btt_eddy]
|
|
#*# calibration_temp = 52.095869
|