[include fluidd.cfg]

[virtual_sdcard]
path: /home/pi/printer_data/gcodes
on_error_gcode: CANCEL_PRINT

[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 2
max_z_accel: 100

[stepper_x]
step_pin: PE3
dir_pin: !PE2
enable_pin: !PE4
microsteps: 16
rotation_distance: 34.64
endstop_pin: ^PA15
position_endstop: 140
position_max: 150
position_min: -10
homing_speed: 50

[tmc2209 stepper_x]
uart_pin: PA10
interpolate: False
run_current: 0.4

[stepper_y]
step_pin: PE0
dir_pin: PB9
enable_pin: !PE1
microsteps: 16
rotation_distance: 34.64
endstop_pin: ^PA12
position_endstop: 0
position_max: 160
homing_speed: 50

[tmc2209 stepper_y]
uart_pin: PA9
interpolate: False
run_current: 0.4

[stepper_z]
step_pin: PB5
dir_pin: !PB4
microsteps: 16
rotation_distance: 0.586
enable_pin: !PB8
endstop_pin: probe:z_virtual_endstop #!PA11 is on board
position_max: 100
position_min: -5
homing_positive_dir: False

[tmc2209 stepper_z]
uart_pin: PC7
interpolate: False
run_current: 0.4

[extruder]
step_pin: PD6
dir_pin: !PD3
enable_pin: !PB3
microsteps: 16
rotation_distance: 16.1693
full_steps_per_rotation: 400
nozzle_diameter: 0.350
filament_diameter: 1.750
max_extrude_only_velocity: 2000
heater_pin: PC3
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC1
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 220

[tmc2209 extruder]
uart_pin: PC13
interpolate: False
run_current: 0.4
#[extruder1]
#step_pin: PC1
#dir_pin: PC3
#enable_pin: !PC7
#heater_pin: PH6
#sensor_pin: PK7
#...

[heater_bed]
heater_pin: PA0
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC0
control: watermark
min_temp: 0
max_temp: 130

[heater_fan heatbreak_cooling_fan]
pin: PB1
heater: extruder

[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
restart_method: command

[force_move]
enable_force_move: true

[include eddy.cfg]

[safe_z_home]
home_xy_position: 75,75
z_hop: 2

[screws_tilt_adjust]
#screw1=0,95+33 (eddy offset)
screw1=0,128
screw1_name=Left Screw
#screw2=135,57+33
screw2=135,90
screw2_name=Back Right Screw
#screw3=135,105
screw3=135,138
screw3_name=Front Right Screw
screw_thread: CW-M3
speed=60
horizontal_move_z=5

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [probe_eddy_current btt_eddy]
#*# reg_drive_current = 15
#*# calibrate =
#*# 	0.049993:3223222.398,0.089914:3222696.923,0.130019:3222199.447,
#*# 	0.169940:3221583.608,0.210044:3220854.994,0.249966:3220183.661,
#*# 	0.290070:3219155.391,0.329991:3218089.993,0.369913:3217043.071,
#*# 	0.410017:3215993.543,0.449938:3214994.125,0.490042:3214112.086,
#*# 	0.529964:3213156.046,0.570068:3212314.775,0.609989:3211459.497,
#*# 	0.649911:3210584.734,0.690015:3209689.801,0.729936:3208836.978,
#*# 	0.770041:3208023.010,0.809962:3207289.863,0.850066:3206599.916,
#*# 	0.889987:3205856.377,0.929909:3205162.218,0.970013:3204410.580,
#*# 	1.009934:3203712.190,1.050039:3203027.201,1.089960:3202390.155,
#*# 	1.130064:3201851.496,1.169986:3201312.538,1.210090:3200748.371,
#*# 	1.250011:3200155.821,1.289932:3199526.630,1.330037:3198942.050,
#*# 	1.369958:3198403.403,1.410062:3197912.325,1.449984:3197467.804,
#*# 	1.490088:3196993.739,1.530009:3196530.609,1.569931:3196055.573,
#*# 	1.610035:3195604.458,1.649956:3195164.639,1.690061:3194758.705,
#*# 	1.729982:3194420.552,1.770086:3194061.651,1.810007:3193662.164,
#*# 	1.849929:3193280.855,1.890033:3192880.718,1.929954:3192454.578,
#*# 	1.970059:3192095.084,2.009980:3191755.446,2.050084:3191461.052,
#*# 	2.090006:3191133.031,2.129927:3190756.179,2.170031:3190426.959,
#*# 	2.209952:3190113.023,2.250057:3189810.939,2.289978:3189526.494,
#*# 	2.330083:3189259.488,2.370004:3188972.679,2.409925:3188685.028,
#*# 	2.450029:3188393.125,2.489951:3188135.144,2.530055:3187873.523,
#*# 	2.569976:3187603.802,2.610081:3187382.983,2.650002:3187159.872,
#*# 	2.689923:3186914.049,2.730028:3186656.198,2.769949:3186424.967,
#*# 	2.810053:3186209.097,2.849974:3185999.953,2.890079:3185809.227,
#*# 	2.930000:3185599.575,2.969921:3185419.073,3.010026:3185205.074,
#*# 	3.049947:3184994.248,3.090051:3184782.938,3.129973:3184600.146,
#*# 	3.170077:3184415.406,3.209998:3184252.974,3.249919:3184095.122,
#*# 	3.290024:3183909.897,3.329945:3183742.613,3.370049:3183578.689,
#*# 	3.409971:3183409.556,3.450075:3183260.146,3.489996:3183104.085,
#*# 	3.529918:3182972.688,3.570022:3182810.155,3.609943:3182680.368,
#*# 	3.650048:3182547.452,3.689969:3182392.135,3.730073:3182253.435,
#*# 	3.769994:3182126.620,3.809916:3182014.604,3.850020:3181875.583,
#*# 	3.889941:3181740.096,3.930046:3181596.221,3.969967:3181451.014,
#*# 	4.010071:3181380.168,4.049993:3181262.890
#*#
#*# [temperature_probe btt_eddy]
#*# calibration_temp = 52.095869