522 lines
14 KiB
INI
522 lines
14 KiB
INI
# This file contains common pin mappings for the BigTreeTech Octopus V1.
|
|
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
|
|
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
|
|
|
|
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
|
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] and [heater_bed] sections - See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types
|
|
## Z Endstop Switch location [safe_z_home] section
|
|
## Homing end position [gcode_macro G32] section
|
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
|
## Probe points [quad_gantry_level] section
|
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
|
## PID tune [extruder] and [heater_bed] sections
|
|
## Probe pin [probe] section
|
|
## Fine tune E steps [extruder] section
|
|
|
|
[mcu]
|
|
canbus_uuid: 970febd72165
|
|
|
|
[include ebb36.cfg]
|
|
#[include klicky-probe.cfg]
|
|
#[include klicky-quad-gantry-level.cfg]
|
|
[include fluidd.cfg]
|
|
[include stealthburner_leds.cfg]
|
|
[include bedfans.cfg]
|
|
[include martyn_macros.cfg]
|
|
[include shaketune.cfg]
|
|
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 700
|
|
max_accel: 3300 #Max 4000
|
|
max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 350
|
|
square_corner_velocity: 5.0
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
## B Stepper - Left
|
|
## Connected to MOTOR_0
|
|
## Endstop connected to DIAG_0
|
|
[stepper_x]
|
|
step_pin: PF13
|
|
dir_pin: PF12
|
|
enable_pin: !PF14
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 200 for 1.8 degree stepper
|
|
endstop_pin: PG6
|
|
position_min: 0
|
|
position_endstop: 345
|
|
position_max: 345
|
|
homing_speed: 50 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC4
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## A Stepper - Right
|
|
## Connected to MOTOR_1
|
|
## Endstop connected to DIAG_1
|
|
[stepper_y]
|
|
step_pin: PG0
|
|
dir_pin: PG1
|
|
enable_pin: !PF15
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 200 for 1.8 degree stepper
|
|
endstop_pin: PG9
|
|
position_min: 0
|
|
position_endstop: 350
|
|
position_max: 350
|
|
homing_speed: 50 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PD11
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## Z0 Stepper - Front Left
|
|
## Connected to MOTOR_2
|
|
## Endstop connected to DIAG_2
|
|
[stepper_z]
|
|
step_pin: PF11
|
|
dir_pin: PG3
|
|
enable_pin: !PG5
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
#endstop_pin: PG10
|
|
endstop_pin:probe:z_virtual_endstop
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
#position_endstop: -0.5
|
|
position_max: 310
|
|
position_min: -10
|
|
homing_speed: 15
|
|
second_homing_speed: 3
|
|
homing_retract_dist: 3
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC6
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z1 Stepper - Rear Left
|
|
## Connected to MOTOR_3
|
|
[stepper_z1]
|
|
step_pin: PG4
|
|
dir_pin: !PC1
|
|
enable_pin: !PA0
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PC7
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z2 Stepper - Rear Right
|
|
## Connected to MOTOR_4
|
|
[stepper_z2]
|
|
step_pin: PF9
|
|
dir_pin: PF10
|
|
enable_pin: !PG2
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PF2
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z3 Stepper - Front Right
|
|
## Connected to MOTOR_5
|
|
[stepper_z3]
|
|
step_pin: PC13
|
|
dir_pin: !PF0
|
|
enable_pin: !PF1
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PE4
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
|
|
## SSR Pin - HE1
|
|
## Thermistor - TB
|
|
[heater_bed]
|
|
heater_pin: PA1
|
|
## Validate the following thermistor type to make sure it is correct
|
|
## Keenovo branded bed heaters should use Generic 3950
|
|
## LDO branded bed heaters will have the sensor type labelled on the heater
|
|
## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types.
|
|
## Use "Generic 3950" for Keenovo heaters
|
|
sensor_type: ATC Semitec 104NT-4-R025H42G
|
|
sensor_pin: PF3
|
|
## Adjust Max Power so your heater doesn't warp your bed. Rule of thumb is 0.4 watts / cm^2 .
|
|
max_power: 0.6
|
|
min_temp: 0
|
|
max_temp: 120
|
|
control: pid
|
|
pid_kp: 58.437
|
|
pid_ki: 2.347
|
|
pid_kd: 363.769
|
|
|
|
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
|
|
|
|
## Controller fan - FAN2
|
|
[controller_fan controller_fan]
|
|
pin: PD12
|
|
kick_start_time: 0.5
|
|
heater: heater_bed
|
|
fan_speed: 0.5
|
|
|
|
## Exhaust fan - FAN3
|
|
#[heater_fan exhaust_fan]
|
|
#pin: PD13
|
|
#max_power: 1.0
|
|
#shutdown_speed: 0.0
|
|
#kick_start_time: 5.0
|
|
#heater: heater_bed
|
|
#heater_temp: 60
|
|
#fan_speed: 1.0
|
|
|
|
#####################################################################
|
|
# LED Control
|
|
#####################################################################
|
|
|
|
[output_pin caselight]
|
|
## Chamber Lighting - CNC_FAN5
|
|
pin: PD15
|
|
pwm:true
|
|
shutdown_value: 0
|
|
value:1
|
|
cycle_time: 0.01
|
|
|
|
#####################################################################
|
|
# Additional Sensors
|
|
#####################################################################
|
|
|
|
[thermistor CMFB103F3950FANT]
|
|
temperature1: 0.0
|
|
resistance1: 32116.0
|
|
temperature2: 40.0
|
|
resistance2: 5309.0
|
|
temperature3: 80.0
|
|
resistance3: 1228.0
|
|
|
|
# [temperature_sensor chamber_temp]
|
|
# # Chamber Temperature - T1
|
|
# sensor_type: ATC Semitec 104NT-4-R025H42G
|
|
# sensor_pin: PF5
|
|
# min_temp: 0
|
|
# max_temp: 100
|
|
# gcode_id: chamber_th
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
timeout: 1800
|
|
|
|
# Klicky probe replaces this!
|
|
[safe_z_home]
|
|
## XY Location of the Z Endstop Switch
|
|
## Update -10,-10 to the XY coordinates of your endstop pin
|
|
## (such as 157,305) after going through Z Endstop Pin
|
|
## Location Definition step.
|
|
#home_xy_position:232,350
|
|
home_xy_position: 175,175
|
|
speed:100
|
|
z_hop:10
|
|
z_hop_speed:10
|
|
|
|
|
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
|
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
|
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
|
## to respective belt positions
|
|
[quad_gantry_level]
|
|
gantry_corners:
|
|
-60,-10
|
|
410,420
|
|
# Probe points
|
|
points:
|
|
50,25
|
|
50,275
|
|
300,275
|
|
300,25
|
|
|
|
speed: 100
|
|
horizontal_move_z: 10
|
|
retries: 5
|
|
retry_tolerance: 0.04
|
|
max_adjust: 10
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PE8, EXP1_2=PE7,
|
|
EXP1_3=PE9, EXP1_4=PE10,
|
|
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
|
|
EXP1_7=PE14, EXP1_8=PE15,
|
|
EXP1_9=<GND>, EXP1_10=<5V>,
|
|
|
|
# EXP2 header
|
|
EXP2_1=PA6, EXP2_2=PA5,
|
|
EXP2_3=PB1, EXP2_4=PA4,
|
|
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
|
|
EXP2_7=PC15, EXP2_8=<RST>,
|
|
EXP2_9=<GND>, EXP2_10=<5V>
|
|
|
|
#####################################################################
|
|
# Displays
|
|
#####################################################################
|
|
|
|
[display]
|
|
# mini12864 LCD Display
|
|
lcd_type: uc1701
|
|
cs_pin: EXP1_3
|
|
a0_pin: EXP1_4
|
|
rst_pin: EXP1_5
|
|
encoder_pins: ^EXP2_5, ^EXP2_3
|
|
click_pin: ^!EXP1_2
|
|
contrast: 63
|
|
spi_software_miso_pin: EXP2_1
|
|
spi_software_mosi_pin: EXP2_6
|
|
spi_software_sclk_pin: EXP2_2
|
|
|
|
[neopixel btt_mini12864]
|
|
# To control Neopixel RGB in mini12864 display
|
|
pin: EXP1_6
|
|
chain_count: 3
|
|
initial_RED: 0.6
|
|
initial_GREEN: 0.0
|
|
initial_BLUE: 0.0
|
|
color_order: RGB
|
|
|
|
## Set RGB values on boot up for each Neopixel.
|
|
## Index 1 = display, Index 2 and 3 = Knob
|
|
[delayed_gcode setdisplayneopixel]
|
|
initial_duration: 1
|
|
gcode:
|
|
SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=0.6 GREEN=0 BLUE=1 INDEX=2 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=0.6 GREEN=0 BLUE=1 INDEX=3
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
[temperature_sensor pi]
|
|
sensor_type: temperature_host
|
|
|
|
[temperature_sensor mcu]
|
|
sensor_type: temperature_mcu
|
|
|
|
[skew_correction]
|
|
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
|
|
|
|
# pre-cartographer
|
|
# [probe]
|
|
# pin: ebb36:PB9
|
|
# x_offset: 0
|
|
# y_offset: 19.75
|
|
# #z_offset: 5.930
|
|
# # below is default, trying -0.365 measured, if +0.365, it's 6.785
|
|
# # z_offset: 6.42
|
|
# speed: 5
|
|
# samples: 3
|
|
# samples_result: median
|
|
# sample_retract_dist: 2.0
|
|
# samples_tolerance: 0.01
|
|
# samples_tolerance_retries: 4
|
|
|
|
[bed_mesh]
|
|
speed: 120
|
|
horizontal_move_z: 2
|
|
mesh_min: 35, 35
|
|
mesh_max: 310, 310
|
|
zero_reference_position: 175, 175
|
|
#probe_count: 5, 5
|
|
probe_count: 5
|
|
mesh_pps: 7, 7
|
|
algorithm: bicubic
|
|
bicubic_tension: 0.2
|
|
probe_count: 7, 7
|
|
|
|
[input_shaper]
|
|
shaper_freq_x: 91.4
|
|
shaper_freq_y: 70.0
|
|
shaper_type: 3hump_ei
|
|
|
|
[cartographer]
|
|
canbus_uuid: 506fcd528089
|
|
# Path to the serial port for the Cartographer device. Typically has the form
|
|
# /dev/serial/by-id/usb-cartographer_cartographer_...
|
|
#
|
|
# If you are using the CAN Bus version, replace serial: with canbus_uuid: and add the UUID.
|
|
# Example: canbus_uuid: 1283as878a9sd
|
|
#
|
|
speed: 40.
|
|
# Z probing dive speed.
|
|
lift_speed: 5.0
|
|
# Z probing lift speed.
|
|
backlash_comp: 0.5
|
|
# Backlash compensation distance for removing Z backlash before measuring
|
|
# the sensor response.
|
|
#
|
|
# Offsets are measured from the centre of your coil, to the tip of your nozzle
|
|
# on a level axis. It is vital that this is accurate.
|
|
#
|
|
x_offset: 0.0
|
|
# X offset of cartographer from the nozzle.
|
|
y_offset: 21.1
|
|
# Y offset of cartographer from the nozzle.
|
|
trigger_distance: 2.0
|
|
# cartographer trigger distance for homing.
|
|
trigger_dive_threshold: 1.5
|
|
# Threshold for range vs dive mode probing. Beyond `trigger_distance +
|
|
# trigger_dive_threshold` a dive will be used.
|
|
trigger_hysteresis: 0.006
|
|
# Hysteresis on trigger threshold for untriggering, as a percentage of the
|
|
# trigger threshold.
|
|
cal_nozzle_z: 0.1
|
|
# Expected nozzle offset after completing manual Z offset calibration.
|
|
cal_floor: 0.1
|
|
# Minimum z bound on sensor response measurement.
|
|
cal_ceil: 5.0
|
|
# Maximum z bound on sensor response measurement.
|
|
cal_speed: 1.0
|
|
# Speed while measuring response curve.
|
|
cal_move_speed: 10.0
|
|
# Speed while moving to position for response curve measurement.
|
|
default_model_name: default
|
|
# Name of default cartographer model to load.
|
|
mesh_main_direction: x
|
|
# Primary travel direction during mesh measurement.
|
|
#mesh_overscan: -1
|
|
# Distance to use for direction changes at mesh line ends. Omit this setting
|
|
# and a default will be calculated from line spacing and available travel.
|
|
mesh_cluster_size: 1
|
|
# Radius of mesh grid point clusters.
|
|
mesh_runs: 2
|
|
# Number of passes to make during mesh scan.
|
|
|
|
[force_move]
|
|
enable_force_move: True
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [stepper_z]
|
|
#*# position_endstop = -0.595
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# -0.014231, -0.016803, -0.005844, -0.005836, 0.010657, 0.010721, -0.007359
|
|
#*# -0.018001, -0.013551, -0.005853, -0.007854, 0.001696, -0.003069, -0.016462
|
|
#*# -0.013773, -0.025605, -0.015186, -0.015564, -0.005366, -0.008602, -0.030942
|
|
#*# -0.011286, -0.003828, -0.003132, 0.001329, -0.002569, -0.002467, -0.015689
|
|
#*# 0.001846, -0.003048, 0.006619, -0.001119, 0.011636, 0.008508, -0.017133
|
|
#*# -0.013421, -0.007607, 0.006917, -0.007347, 0.010865, 0.007822, -0.013145
|
|
#*# 0.006005, 0.004915, 0.017569, 0.008505, 0.024801, 0.030391, 0.000916
|
|
#*# x_count = 7
|
|
#*# y_count = 7
|
|
#*# mesh_x_pps = 7
|
|
#*# mesh_y_pps = 7
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*# min_x = 35.0
|
|
#*# max_x = 310.0
|
|
#*# min_y = 35.0
|
|
#*# max_y = 310.0
|
|
#*#
|
|
#*# [probe]
|
|
#*# z_offset = 7.600
|
|
#*#
|
|
#*# [skew_correction calilantern_skew_profile]
|
|
#*# xy_skew = 0.008146115207013459
|
|
#*# xz_skew = 0.0008273174781853165
|
|
#*# yz_skew = -0.00037476759249049555
|
|
#*#
|
|
#*# [cartographer model default]
|
|
#*# model_coef = 1.2383244430293725,
|
|
#*# 1.6631086108008772,
|
|
#*# 0.7502926632060991,
|
|
#*# 0.3324317142939241,
|
|
#*# 0.5155928496660419,
|
|
#*# 0.6156244841720987,
|
|
#*# -0.41471347202364395,
|
|
#*# -0.5737807217363379,
|
|
#*# 0.4603036209624226,
|
|
#*# 0.41315535784273816
|
|
#*# model_domain = 3.0373112811055786e-07,3.3148137270365367e-07
|
|
#*# model_range = 0.100000,5.000000
|
|
#*# model_temp = 28.999113
|
|
#*# model_offset = 0.46500
|