505 lines
13 KiB
INI
505 lines
13 KiB
INI
[include mmu/base/*.cfg]
|
|
[include mmu/optional/client_macros.cfg]
|
|
[include mmu/optional/mmu_menu.cfg]
|
|
# This file contains common pin mappings for the BigTreeTech Octopus V1.
|
|
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
|
|
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
|
|
|
|
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
|
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] and [heater_bed] sections - See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types
|
|
## Z Endstop Switch location [safe_z_home] section
|
|
## Homing end position [gcode_macro G32] section
|
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
|
## Probe points [quad_gantry_level] section
|
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
|
## PID tune [extruder] and [heater_bed] sections
|
|
## Probe pin [probe] section
|
|
## Fine tune E steps [extruder] section
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_210044000150335331383520-if00
|
|
# no longer a canbus bridge
|
|
#canbus_uuid: 970febd72165
|
|
|
|
[include ebb36.cfg]
|
|
#[include klicky-probe.cfg]
|
|
#[include klicky-quad-gantry-level.cfg]
|
|
[include fluidd.cfg]
|
|
[include stealthburner_leds.cfg]
|
|
[include bedfans.cfg]
|
|
[include martyn_macros.cfg]
|
|
[include shaketune.cfg]
|
|
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 700
|
|
max_accel: 3300 #Max 4000
|
|
max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 350
|
|
square_corner_velocity: 5.0
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
## B Stepper - Left
|
|
## Connected to MOTOR_0
|
|
## Endstop connected to DIAG_0
|
|
[stepper_x]
|
|
step_pin: PF13
|
|
dir_pin: PF12
|
|
enable_pin: !PF14
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 200 for 1.8 degree stepper
|
|
endstop_pin: PG6
|
|
position_min: 0
|
|
position_endstop: 345
|
|
position_max: 345
|
|
homing_speed: 50 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC4
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## A Stepper - Right
|
|
## Connected to MOTOR_1
|
|
## Endstop connected to DIAG_1
|
|
[stepper_y]
|
|
step_pin: PG0
|
|
dir_pin: PG1
|
|
enable_pin: !PF15
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 200 for 1.8 degree stepper
|
|
endstop_pin: PG9
|
|
position_min: 0
|
|
position_endstop: 355
|
|
position_max: 355
|
|
homing_speed: 50 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PD11
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## Z0 Stepper - Front Left
|
|
## Connected to MOTOR_2
|
|
## Endstop connected to DIAG_2
|
|
[stepper_z]
|
|
step_pin: PF11
|
|
dir_pin: PG3
|
|
enable_pin: !PG5
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
#endstop_pin: PG10
|
|
endstop_pin:probe:z_virtual_endstop
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
#position_endstop: -0.5
|
|
position_max: 310
|
|
position_min: -10
|
|
homing_speed: 15
|
|
second_homing_speed: 3
|
|
homing_retract_dist: 3
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC6
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z1 Stepper - Rear Left
|
|
## Connected to MOTOR_3
|
|
[stepper_z1]
|
|
step_pin: PG4
|
|
dir_pin: !PC1
|
|
enable_pin: !PA0
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PC7
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z2 Stepper - Rear Right
|
|
## Connected to MOTOR_4
|
|
[stepper_z2]
|
|
step_pin: PF9
|
|
dir_pin: PF10
|
|
enable_pin: !PG2
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PF2
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z3 Stepper - Front Right
|
|
## Connected to MOTOR_5
|
|
[stepper_z3]
|
|
step_pin: PC13
|
|
dir_pin: !PF0
|
|
enable_pin: !PF1
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PE4
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
|
|
## SSR Pin - HE1
|
|
## Thermistor - TB
|
|
[heater_bed]
|
|
heater_pin: PA1
|
|
## Validate the following thermistor type to make sure it is correct
|
|
## Keenovo branded bed heaters should use Generic 3950
|
|
## LDO branded bed heaters will have the sensor type labelled on the heater
|
|
## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types.
|
|
## Use "Generic 3950" for Keenovo heaters
|
|
sensor_type: ATC Semitec 104NT-4-R025H42G
|
|
sensor_pin: PF3
|
|
## Adjust Max Power so your heater doesn't warp your bed. Rule of thumb is 0.4 watts / cm^2 .
|
|
max_power: 0.6
|
|
min_temp: 0
|
|
max_temp: 120
|
|
control: pid
|
|
pid_kp: 58.437
|
|
pid_ki: 2.347
|
|
pid_kd: 363.769
|
|
|
|
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
|
|
|
|
## Controller fan - FAN2
|
|
[controller_fan controller_fan]
|
|
pin: PD12
|
|
kick_start_time: 0.5
|
|
heater: heater_bed
|
|
fan_speed: 0.5
|
|
|
|
## Exhaust fan - FAN3
|
|
#[heater_fan exhaust_fan]
|
|
#pin: PD13
|
|
#max_power: 1.0
|
|
#shutdown_speed: 0.0
|
|
#kick_start_time: 5.0
|
|
#heater: heater_bed
|
|
#heater_temp: 60
|
|
#fan_speed: 1.0
|
|
|
|
#####################################################################
|
|
# LED Control
|
|
#####################################################################
|
|
|
|
[output_pin caselight]
|
|
## Chamber Lighting - CNC_FAN5
|
|
pin: PD15
|
|
pwm:true
|
|
shutdown_value: 0
|
|
value:1
|
|
cycle_time: 0.01
|
|
|
|
#####################################################################
|
|
# Additional Sensors
|
|
#####################################################################
|
|
|
|
[thermistor CMFB103F3950FANT]
|
|
temperature1: 0.0
|
|
resistance1: 32116.0
|
|
temperature2: 40.0
|
|
resistance2: 5309.0
|
|
temperature3: 80.0
|
|
resistance3: 1228.0
|
|
|
|
# [temperature_sensor chamber_temp]
|
|
# # Chamber Temperature - T1
|
|
# sensor_type: ATC Semitec 104NT-4-R025H42G
|
|
# sensor_pin: PF5
|
|
# min_temp: 0
|
|
# max_temp: 100
|
|
# gcode_id: chamber_th
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
timeout: 1800
|
|
|
|
# Klicky probe replaces this!
|
|
# [safe_z_home]
|
|
# ## XY Location of the Z Endstop Switch
|
|
# ## Update -10,-10 to the XY coordinates of your endstop pin
|
|
# ## (such as 157,305) after going through Z Endstop Pin
|
|
# ## Location Definition step.
|
|
# #home_xy_position:232,350
|
|
# home_xy_position: 175,175
|
|
# speed:100
|
|
# z_hop:10
|
|
# z_hop_speed:10
|
|
|
|
|
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
|
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
|
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
|
## to respective belt positions
|
|
[quad_gantry_level]
|
|
gantry_corners:
|
|
-60,-10
|
|
410,420
|
|
# Probe points
|
|
points:
|
|
50,25
|
|
50,275
|
|
300,275
|
|
300,25
|
|
|
|
speed: 100
|
|
horizontal_move_z: 10
|
|
retries: 5
|
|
retry_tolerance: 0.04
|
|
max_adjust: 10
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PE8, EXP1_2=PE7,
|
|
EXP1_3=PE9, EXP1_4=PE10,
|
|
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
|
|
EXP1_7=PE14, EXP1_8=PE15,
|
|
EXP1_9=<GND>, EXP1_10=<5V>,
|
|
|
|
# EXP2 header
|
|
EXP2_1=PA6, EXP2_2=PA5,
|
|
EXP2_3=PB1, EXP2_4=PA4,
|
|
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
|
|
EXP2_7=PC15, EXP2_8=<RST>,
|
|
EXP2_9=<GND>, EXP2_10=<5V>
|
|
|
|
#####################################################################
|
|
# Displays
|
|
#####################################################################
|
|
|
|
[display]
|
|
# mini12864 LCD Display
|
|
lcd_type: uc1701
|
|
cs_pin: EXP1_3
|
|
a0_pin: EXP1_4
|
|
rst_pin: EXP1_5
|
|
encoder_pins: ^EXP2_5, ^EXP2_3
|
|
click_pin: ^!EXP1_2
|
|
contrast: 63
|
|
spi_software_miso_pin: EXP2_1
|
|
spi_software_mosi_pin: EXP2_6
|
|
spi_software_sclk_pin: EXP2_2
|
|
|
|
[neopixel btt_mini12864]
|
|
# To control Neopixel RGB in mini12864 display
|
|
pin: EXP1_6
|
|
chain_count: 3
|
|
initial_RED: 0.6
|
|
initial_GREEN: 0.0
|
|
initial_BLUE: 0.0
|
|
color_order: RGB
|
|
|
|
## Set RGB values on boot up for each Neopixel.
|
|
## Index 1 = display, Index 2 and 3 = Knob
|
|
[delayed_gcode setdisplayneopixel]
|
|
initial_duration: 1
|
|
gcode:
|
|
SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=0.6 GREEN=0 BLUE=1 INDEX=2 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=0.6 GREEN=0 BLUE=1 INDEX=3
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
[temperature_sensor pi]
|
|
sensor_type: temperature_host
|
|
|
|
[temperature_sensor mcu]
|
|
sensor_type: temperature_mcu
|
|
|
|
[skew_correction]
|
|
|
|
[exclude_object]
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
|
|
|
|
# pre-cartographer
|
|
# [probe]
|
|
# pin: ebb36:PB9
|
|
# x_offset: 0
|
|
# y_offset: 19.75
|
|
# #z_offset: 5.930
|
|
# # below is default, trying -0.365 measured, if +0.365, it's 6.785
|
|
# # z_offset: 6.42
|
|
# speed: 5
|
|
# samples: 3
|
|
# samples_result: median
|
|
# sample_retract_dist: 2.0
|
|
# samples_tolerance: 0.01
|
|
# samples_tolerance_retries: 4
|
|
|
|
[bed_mesh]
|
|
speed: 120
|
|
horizontal_move_z: 2
|
|
mesh_min: 35, 35
|
|
mesh_max: 310, 310
|
|
zero_reference_position: 175, 175
|
|
#probe_count: 5, 5
|
|
probe_count: 5
|
|
mesh_pps: 7, 7
|
|
algorithm: bicubic
|
|
bicubic_tension: 0.2
|
|
probe_count: 7, 7
|
|
|
|
[input_shaper]
|
|
shaper_freq_x: 91.4
|
|
shaper_freq_y: 70.0
|
|
shaper_type: 3hump_ei
|
|
|
|
[mcu scanner]
|
|
canbus_uuid: 4afa67798fac
|
|
|
|
[scanner]
|
|
mcu: scanner
|
|
sensor: cartographer
|
|
sensor_alt: carto
|
|
# Z probing lift speed.
|
|
backlash_comp: 0.5
|
|
# Backlash compensation distance for removing Z backlash before measuring
|
|
# the sensor response.
|
|
#
|
|
# Offsets are measured from the centre of your coil, to the tip of your nozzle
|
|
# on a level axis. It is vital that this is accurate.
|
|
#
|
|
x_offset: 0.0
|
|
# X offset of cartographer from the nozzle.
|
|
y_offset: 21.1
|
|
# Y offset of cartographer from the nozzle.
|
|
mesh_runs: 2
|
|
# Number of passes to make during mesh scan.
|
|
|
|
[force_move]
|
|
enable_force_move: True
|
|
|
|
# Let's not yet...
|
|
#[filament_motion_sensor encoder_sensor]
|
|
#switch_pin: PG12
|
|
#detection_length: 2.88
|
|
#extruder: extruder
|
|
#pause_on_runout: False
|
|
#runout_gcode:
|
|
# PAUSE # [pause_resume] is required in printer.cfg
|
|
# M117 Filament encoder runout
|
|
#insert_gcode:
|
|
# M117 Filament encoder inserted
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [scanner model default]
|
|
#*# model_coef = 1.4050831858687034,
|
|
#*# 1.8219447940830515,
|
|
#*# 0.7738341113330293,
|
|
#*# 0.39901472219479744,
|
|
#*# 0.2680326035724343,
|
|
#*# 0.17965483078663627,
|
|
#*# -0.05775648804119655,
|
|
#*# -0.009252690277367137,
|
|
#*# 0.16228924774561448,
|
|
#*# 0.061116700668611953
|
|
#*# model_domain = 3.2083850283845136e-07,3.3397281426221727e-07
|
|
#*# model_range = 0.100000,5.000000
|
|
#*# model_temp = 46.457695
|
|
#*# model_offset = 0.70000
|
|
#*# model_mode = scan
|
|
#*# model_fw_version = CARTOGRAPHER 5.1.0
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.041161, 0.051208, 0.066799, 0.071546, 0.084688, 0.084895, 0.059104
|
|
#*# 0.014865, 0.032096, 0.049178, 0.054047, 0.048510, 0.049620, 0.025237
|
|
#*# -0.005754, -0.007002, 0.019700, 0.015406, 0.022316, 0.036221, -0.007241
|
|
#*# 0.000396, 0.008555, 0.012480, 0.000716, 0.027217, 0.031460, 0.007651
|
|
#*# 0.022828, 0.027269, 0.041696, 0.026893, 0.043456, 0.038767, 0.010067
|
|
#*# 0.023738, 0.035277, 0.054947, 0.037046, 0.056997, 0.053538, 0.024971
|
|
#*# 0.062581, 0.068327, 0.082214, 0.070779, 0.088493, 0.093656, 0.058708
|
|
#*# x_count = 7
|
|
#*# y_count = 7
|
|
#*# mesh_x_pps = 7
|
|
#*# mesh_y_pps = 7
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*# min_x = 35.0
|
|
#*# max_x = 310.0
|
|
#*# min_y = 35.0
|
|
#*# max_y = 310.0
|
|
#*#
|
|
#*# [skew_correction calilantern_skew_profile]
|
|
#*# xy_skew = 0.007318697823262824
|
|
#*# xz_skew = 0.0004313347372552723
|
|
#*# yz_skew = -0.0005939714989857676
|