509 lines
22 KiB
INI
509 lines
22 KiB
INI
# MMU to be disconnected, so let's have klipper able to run without it.
|
|
#[include mmu/base/*.cfg]
|
|
#[include mmu/optional/client_macros.cfg]
|
|
#[include mmu/optional/mmu_menu.cfg]
|
|
[include timelapse.cfg]
|
|
# This file contains common pin mappings for the BigTreeTech Octopus V1.
|
|
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
|
|
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
|
|
|
|
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
|
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] and [heater_bed] sections - See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types
|
|
## Z Endstop Switch location [safe_z_home] section
|
|
## Homing end position [gcode_macro G32] section
|
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
|
## Probe points [quad_gantry_level] section
|
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
|
## PID tune [extruder] and [heater_bed] sections
|
|
## Probe pin [probe] section
|
|
## Fine tune E steps [extruder] section
|
|
|
|
[mcu]
|
|
# katapulted klipper on can
|
|
canbus_uuid: 970febd72165
|
|
# katapulted klipper on usb
|
|
#serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_210044000150335331383520-if00
|
|
|
|
[include ebb36.cfg]
|
|
[include fluidd.cfg]
|
|
[include stealthburner_leds.cfg]
|
|
[include bedfans.cfg]
|
|
[include martyn_macros.cfg]
|
|
[include carto.cfg]
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 700
|
|
max_accel: 3300 #Max 4000
|
|
max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 350
|
|
square_corner_velocity: 5.0
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
## B Stepper - Left
|
|
## Connected to MOTOR_0
|
|
## Endstop connected to DIAG_0
|
|
[stepper_x]
|
|
step_pin: PF13
|
|
dir_pin: PF12
|
|
enable_pin: !PF14
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 200 for 1.8 degree stepper
|
|
endstop_pin: PG6
|
|
position_min: 0
|
|
position_endstop: 345
|
|
position_max: 345
|
|
homing_speed: 70 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC4
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## A Stepper - Right
|
|
## Connected to MOTOR_1
|
|
## Endstop connected to DIAG_1
|
|
[stepper_y]
|
|
step_pin: PG0
|
|
dir_pin: PG1
|
|
enable_pin: !PF15
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 200 for 1.8 degree stepper
|
|
endstop_pin: PG9
|
|
position_min: 0
|
|
position_endstop: 355
|
|
position_max: 355
|
|
homing_speed: 70 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PD11
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## Z0 Stepper - Front Left
|
|
## Connected to MOTOR_2
|
|
## Endstop connected to DIAG_2
|
|
[stepper_z]
|
|
step_pin: PF11
|
|
dir_pin: PG3
|
|
enable_pin: !PG5
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
endstop_pin: probe:z_virtual_endstop
|
|
#endstop_pin: !ebb36:PB7
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
#position_endstop: 0
|
|
position_max: 310
|
|
position_min: -5
|
|
homing_speed: 15
|
|
#second_homing_speed: 3
|
|
#homing_retract_dist: 3
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC6
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z1 Stepper - Rear Left
|
|
## Connected to MOTOR_3
|
|
[stepper_z1]
|
|
step_pin: PG4
|
|
dir_pin: !PC1
|
|
enable_pin: !PA0
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PC7
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z2 Stepper - Rear Right
|
|
## Connected to MOTOR_4
|
|
[stepper_z2]
|
|
step_pin: PF9
|
|
dir_pin: PF10
|
|
enable_pin: !PG2
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PF2
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z3 Stepper - Front Right
|
|
## Connected to MOTOR_5
|
|
[stepper_z3]
|
|
step_pin: PC13
|
|
dir_pin: !PF0
|
|
enable_pin: !PF1
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PE4
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
|
|
## SSR Pin - HE1
|
|
## Thermistor - TB
|
|
[heater_bed]
|
|
heater_pin: PA1
|
|
## Validate the following thermistor type to make sure it is correct
|
|
## Keenovo branded bed heaters should use Generic 3950
|
|
## LDO branded bed heaters will have the sensor type labelled on the heater
|
|
## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types.
|
|
## Use "Generic 3950" for Keenovo heaters
|
|
sensor_type: ATC Semitec 104NT-4-R025H42G
|
|
sensor_pin: PF3
|
|
## Adjust Max Power so your heater doesn't warp your bed. Rule of thumb is 0.4 watts / cm^2 .
|
|
max_power: 0.6
|
|
min_temp: 0
|
|
max_temp: 120
|
|
control: pid
|
|
pid_Kp: 43.209
|
|
pid_Ki: 1.162
|
|
pid_Kd: 401.841
|
|
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
|
|
|
|
## Controller fan - FAN2
|
|
[temperature_fan controller_fan]
|
|
pin: PD12
|
|
sensor_type: temperature_host
|
|
control: watermark
|
|
max_delta: 3
|
|
min_temp: 0
|
|
max_temp: 100
|
|
target_temp: 55
|
|
max_speed: 0.5
|
|
|
|
## Exhaust fan - FAN3
|
|
#[heater_fan exhaust_fan]
|
|
#pin: PD13
|
|
#max_power: 1.0
|
|
#shutdown_speed: 0.0
|
|
#kick_start_time: 5.0
|
|
#heater: heater_bed
|
|
#heater_temp: 60
|
|
#fan_speed: 1.0
|
|
|
|
#####################################################################
|
|
# LED Control
|
|
#####################################################################
|
|
|
|
[output_pin caselight]
|
|
## Chamber Lighting - CNC_FAN5
|
|
pin: PD15
|
|
pwm:true
|
|
shutdown_value: 0
|
|
value:1
|
|
cycle_time: 0.01
|
|
|
|
#####################################################################
|
|
# Additional Sensors
|
|
#####################################################################
|
|
|
|
[thermistor CMFB103F3950FANT]
|
|
temperature1: 0.0
|
|
resistance1: 32116.0
|
|
temperature2: 40.0
|
|
resistance2: 5309.0
|
|
temperature3: 80.0
|
|
resistance3: 1228.0
|
|
|
|
[temperature_sensor chamber_temp]
|
|
# Chamber Temperature - T1
|
|
sensor_type: EPCOS 100K B57560G104F # total guess really, but sure.
|
|
sensor_pin: PF5
|
|
min_temp: 0
|
|
max_temp: 100
|
|
gcode_id: chamber_th
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
timeout: 1800
|
|
|
|
# Need to work out how eddy interferes with magic home
|
|
#[safe_z_home]
|
|
#home_xy_position: 175,175
|
|
#speed:100
|
|
#z_hop:10
|
|
#z_hop_speed:10
|
|
|
|
[homing_override]
|
|
axes: z
|
|
gcode:
|
|
SET_KINEMATIC_POSITION Z=0
|
|
G1 Z10 F3000
|
|
{% if not 'X' in printer.toolhead.homed_axes %}
|
|
G28 X0
|
|
{% endif %}
|
|
{% if not 'Y' in printer.toolhead.homed_axes %}
|
|
G28 Y0
|
|
{% endif %}
|
|
G1 X150 Y150 F3000
|
|
G28 Z0
|
|
G1 Z10 F3000
|
|
|
|
|
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
|
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
|
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
|
## to respective belt positions
|
|
[quad_gantry_level]
|
|
gantry_corners:
|
|
-60,-10
|
|
410,420
|
|
# Probe points
|
|
points:
|
|
50,25
|
|
50,275
|
|
300,275
|
|
300,25
|
|
|
|
speed: 100
|
|
horizontal_move_z: 2
|
|
retries: 5
|
|
retry_tolerance: 0.04
|
|
max_adjust: 10
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PE8, EXP1_2=PE7,
|
|
EXP1_3=PE9, EXP1_4=PE10,
|
|
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
|
|
EXP1_7=PE14, EXP1_8=PE15,
|
|
EXP1_9=<GND>, EXP1_10=<5V>,
|
|
|
|
# EXP2 header
|
|
EXP2_1=PA6, EXP2_2=PA5,
|
|
EXP2_3=PB1, EXP2_4=PA4,
|
|
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
|
|
EXP2_7=PC15, EXP2_8=<RST>,
|
|
EXP2_9=<GND>, EXP2_10=<5V>
|
|
|
|
#####################################################################
|
|
# Displays
|
|
#####################################################################
|
|
|
|
[display]
|
|
# mini12864 LCD Display
|
|
lcd_type: uc1701
|
|
cs_pin: EXP1_3
|
|
a0_pin: EXP1_4
|
|
rst_pin: EXP1_5
|
|
encoder_pins: ^EXP2_5, ^EXP2_3
|
|
click_pin: ^!EXP1_2
|
|
contrast: 63
|
|
spi_software_miso_pin: EXP2_1
|
|
spi_software_mosi_pin: EXP2_6
|
|
spi_software_sclk_pin: EXP2_2
|
|
|
|
[neopixel btt_mini12864]
|
|
# To control Neopixel RGB in mini12864 display
|
|
pin: EXP1_6
|
|
chain_count: 3
|
|
initial_RED: 0.6
|
|
initial_GREEN: 0.0
|
|
initial_BLUE: 0.0
|
|
color_order: RGB
|
|
|
|
## Set RGB values on boot up for each Neopixel.
|
|
## Index 1 = display, Index 2 and 3 = Knob
|
|
[delayed_gcode setdisplayneopixel]
|
|
initial_duration: 1
|
|
gcode:
|
|
SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=0.6 GREEN=0 BLUE=1 INDEX=2 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=0.6 GREEN=0 BLUE=1 INDEX=3
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
[temperature_sensor pi]
|
|
sensor_type: temperature_host
|
|
|
|
[temperature_sensor mcu]
|
|
sensor_type: temperature_mcu
|
|
|
|
[skew_correction]
|
|
|
|
[exclude_object]
|
|
|
|
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
|
|
#[probe] ## Other parameters in config.cfg
|
|
#pin: !ebb36:PB7
|
|
#x_offset: 0.0
|
|
#y_offset: 0.0
|
|
#z_offset: 0.0
|
|
#speed: 15.0 # Speed (in mm/s) of the Z axis when probing. The default is 5mm/s.
|
|
#samples: 2
|
|
#sample_retract_dist: 3.0
|
|
#samples_tolerance_retries: 1
|
|
#lift_speed: 10
|
|
#activate_gcode:
|
|
# G4 P200 ;Wait 200ms
|
|
# SET_TMC_CURRENT STEPPER=stepper_z CURRENT=0.4
|
|
# SET_TMC_CURRENT STEPPER=stepper_z1 CURRENT=0.4
|
|
# SET_TMC_CURRENT STEPPER=stepper_z2 CURRENT=0.4
|
|
# SET_TMC_CURRENT STEPPER=stepper_z3 CURRENT=0.4
|
|
#deactivate_gcode:
|
|
# {% set run_current = printer.configfile.config['tmc2209 stepper_z'].run_current | float %}
|
|
# SET_TMC_CURRENT STEPPER=stepper_z CURRENT={run_current}
|
|
# SET_TMC_CURRENT STEPPER=stepper_z1 CURRENT={run_current}
|
|
# SET_TMC_CURRENT STEPPER=stepper_z2 CURRENT={run_current}
|
|
# SET_TMC_CURRENT STEPPER=stepper_z3 CURRENT={run_current}
|
|
|
|
[input_shaper]
|
|
shaper_freq_x: 91.4
|
|
shaper_freq_y: 70.0
|
|
shaper_type: 3hump_ei
|
|
|
|
[force_move]
|
|
enable_force_move: True
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [skew_correction calilantern_skew_profile]
|
|
#*# xy_skew = 0.002269819397871509
|
|
#*# xz_skew = 0.0
|
|
#*# yz_skew = 0.0
|
|
#*#
|
|
#*# [scanner]
|
|
#*# mode = touch
|
|
#*# scanner_touch_threshold = 750
|
|
#*# scanner_touch_speed = 2
|
|
#*# scanner_touch_z_offset = 0.105
|
|
#*#
|
|
#*# [scanner model default]
|
|
#*# model_coef = 1.54547696704748,
|
|
#*# 1.9826316137382953,
|
|
#*# 0.7339776131866772,
|
|
#*# 0.30422507330624265,
|
|
#*# 0.3176616902930693,
|
|
#*# 0.2617860932937524,
|
|
#*# -0.22258329370910082,
|
|
#*# -0.21919831625292302,
|
|
#*# 0.17974948476952415,
|
|
#*# 0.12614743068240433
|
|
#*# model_domain = 3.298780241186128e-07,3.347286858645663e-07
|
|
#*# model_range = 0.100000,5.000000
|
|
#*# model_temp = 41.081679
|
|
#*# model_offset = 0.00000
|
|
#*# model_mode = touch
|
|
#*# model_fw_version = CARTOGRAPHER 5.0.0
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.045973, 0.040708, 0.038679, 0.034636, 0.027358, 0.026712, 0.019957, 0.020399, 0.020445, 0.024028, 0.025289, 0.024091, 0.027903, 0.025521, 0.022725, 0.023285, 0.015893, 0.020550, 0.027837, 0.036538, 0.051204, 0.054653, 0.058183, 0.050592, 0.051048, 0.049584, 0.046978, 0.044398, 0.044806, 0.047167
|
|
#*# 0.043168, 0.040408, 0.039575, 0.041380, 0.033980, 0.029809, 0.025489, 0.025063, 0.022729, 0.027201, 0.027409, 0.027974, 0.027243, 0.026510, 0.022304, 0.017562, 0.017583, 0.022251, 0.031853, 0.042791, 0.051138, 0.059191, 0.061855, 0.059372, 0.055459, 0.050891, 0.049912, 0.046961, 0.045723, 0.050288
|
|
#*# 0.042510, 0.041342, 0.041796, 0.040952, 0.036391, 0.029995, 0.027662, 0.029671, 0.028260, 0.026922, 0.025386, 0.027770, 0.025195, 0.024871, 0.022858, 0.016278, 0.013349, 0.020582, 0.029274, 0.042506, 0.048842, 0.057476, 0.060415, 0.060397, 0.056403, 0.048314, 0.047780, 0.046280, 0.046934, 0.045677
|
|
#*# 0.035535, 0.037395, 0.039039, 0.035842, 0.032685, 0.027416, 0.027742, 0.026332, 0.025059, 0.023265, 0.023289, 0.022997, 0.023017, 0.022248, 0.018075, 0.015598, 0.013330, 0.018002, 0.024125, 0.033294, 0.045765, 0.054653, 0.058569, 0.056452, 0.051567, 0.046158, 0.041667, 0.040106, 0.040736, 0.043528
|
|
#*# 0.029689, 0.030878, 0.031626, 0.032033, 0.028526, 0.027622, 0.026220, 0.025020, 0.023188, 0.026244, 0.023619, 0.022336, 0.022454, 0.020245, 0.016284, 0.013343, 0.014483, 0.016092, 0.023888, 0.033189, 0.040803, 0.051965, 0.059942, 0.056536, 0.051543, 0.044911, 0.045995, 0.039034, 0.036506, 0.041240
|
|
#*# 0.021806, 0.024018, 0.027809, 0.027815, 0.027340, 0.023814, 0.020441, 0.019773, 0.022995, 0.022210, 0.022012, 0.022299, 0.022138, 0.021631, 0.018334, 0.017453, 0.014645, 0.017763, 0.022620, 0.032151, 0.043383, 0.050660, 0.055332, 0.054712, 0.050628, 0.046020, 0.044602, 0.040257, 0.037089, 0.041367
|
|
#*# 0.022659, 0.022636, 0.027358, 0.027363, 0.025231, 0.021382, 0.018018, 0.019327, 0.020740, 0.022690, 0.021385, 0.022141, 0.020599, 0.019381, 0.018342, 0.017065, 0.013458, 0.013411, 0.016928, 0.029715, 0.042358, 0.048284, 0.051187, 0.052513, 0.048549, 0.050563, 0.043676, 0.038755, 0.037541, 0.041224
|
|
#*# 0.020209, 0.019579, 0.023959, 0.025327, 0.022668, 0.018837, 0.018014, 0.016063, 0.018036, 0.019394, 0.019884, 0.020834, 0.021476, 0.020716, 0.020535, 0.017771, 0.013867, 0.013595, 0.019519, 0.027942, 0.036698, 0.045856, 0.050799, 0.052602, 0.050555, 0.048282, 0.045126, 0.041316, 0.039105, 0.043965
|
|
#*# 0.019846, 0.020619, 0.022691, 0.022858, 0.023787, 0.022393, 0.018039, 0.014321, 0.018041, 0.019715, 0.018259, 0.019537, 0.018518, 0.018951, 0.017726, 0.013931, 0.013494, 0.013247, 0.017460, 0.026971, 0.037688, 0.043672, 0.045993, 0.050209, 0.051174, 0.049559, 0.045723, 0.040796, 0.040912, 0.041482
|
|
#*# 0.013082, 0.014166, 0.018007, 0.018041, 0.018593, 0.014619, 0.011273, 0.004383, 0.008768, 0.010590, 0.011584, 0.013344, 0.013093, 0.011272, 0.008712, 0.005706, 0.004841, 0.008461, 0.013497, 0.022803, 0.030328, 0.037013, 0.041409, 0.042491, 0.043975, 0.042222, 0.039654, 0.035497, 0.031912, 0.033798
|
|
#*# 0.007349, 0.008529, 0.011617, 0.013349, 0.011992, 0.005311, 0.003307, 0.000061, 0.000605, -0.000100, 0.001403, 0.002045, 0.003917, 0.002474, -0.003152, -0.005506, -0.005138, -0.000594, 0.005106, 0.015458, 0.022267, 0.027945, 0.032324, 0.034351, 0.034386, 0.032386, 0.028609, 0.024978, 0.023851, 0.026281
|
|
#*# 0.003976, 0.007252, 0.010781, 0.009819, 0.008664, 0.003833, -0.001821, -0.004662, -0.002548, -0.001301, -0.000783, -0.000769, -0.000725, -0.000785, -0.004671, -0.005507, -0.005582, -0.002173, 0.003867, 0.009785, 0.017941, 0.024616, 0.029685, 0.031754, 0.031911, 0.027862, 0.023841, 0.022986, 0.023236, 0.026265
|
|
#*# 0.004095, 0.003935, -0.000781, 0.000603, 0.003862, 0.000588, -0.003145, -0.005951, -0.004489, -0.003144, -0.003127, -0.004317, -0.000951, -0.001874, -0.005870, -0.004431, -0.007727, -0.004357, 0.005115, 0.008261, 0.012393, 0.020411, 0.027965, 0.030229, 0.034316, 0.029164, 0.023860, 0.020793, 0.020791, 0.022366
|
|
#*# 0.003938, 0.003885, 0.000517, 0.001706, 0.003933, 0.003409, 0.000573, -0.000789, -0.004743, -0.003527, -0.000839, -0.001431, -0.000890, -0.000500, -0.000456, -0.005471, -0.001889, -0.000775, 0.005795, 0.008648, 0.015644, 0.020820, 0.027542, 0.032443, 0.031706, 0.027524, 0.023776, 0.022285, 0.020791, 0.027072
|
|
#*# 0.005876, 0.002837, -0.000749, 0.002403, 0.008648, 0.008662, 0.007820, 0.003971, 0.001467, 0.000109, 0.000292, 0.001473, 0.002864, 0.000834, -0.000107, 0.004248, 0.000962, 0.001561, 0.008283, 0.013277, 0.018304, 0.025021, 0.028535, 0.031851, 0.036151, 0.032856, 0.026325, 0.023309, 0.026371, 0.031868
|
|
#*# 0.007499, 0.004275, 0.003939, 0.005067, 0.008648, 0.013191, 0.012175, 0.008815, 0.003938, 0.003934, 0.008611, 0.006315, 0.005299, 0.004077, 0.002778, 0.000000, 0.000103, 0.001380, 0.006295, 0.012151, 0.020589, 0.025168, 0.029488, 0.030912, 0.036457, 0.037503, 0.036687, 0.027358, 0.030073, 0.037184
|
|
#*# 0.009450, 0.008231, 0.004443, 0.007511, 0.013295, 0.013351, 0.013343, 0.008977, 0.005242, 0.007534, 0.003496, 0.008611, 0.007618, 0.003053, -0.000866, -0.000783, -0.000671, 0.001667, 0.007330, 0.011555, 0.019121, 0.025028, 0.032028, 0.034959, 0.037169, 0.037910, 0.037009, 0.034366, 0.032521, 0.035240
|
|
#*# 0.008646, 0.009713, 0.005079, 0.009052, 0.011014, 0.011003, 0.008921, 0.009511, 0.005079, 0.006622, 0.002863, 0.013324, 0.006307, 0.003404, -0.002197, -0.005809, -0.005472, 0.003938, 0.003441, 0.008647, 0.020302, 0.029742, 0.029721, 0.034203, 0.039302, 0.040013, 0.038468, 0.030974, 0.030258, 0.034351
|
|
#*# 0.014927, 0.014901, 0.009628, 0.012273, 0.012414, 0.013383, 0.013454, 0.008578, 0.004499, 0.008550, 0.004900, 0.012134, 0.008504, 0.003930, 0.000539, -0.000780, -0.000798, 0.003025, 0.008375, 0.014500, 0.022725, 0.027420, 0.033373, 0.041240, 0.041293, 0.040199, 0.034081, 0.032041, 0.032028, 0.034597
|
|
#*# 0.018082, 0.020351, 0.015936, 0.018041, 0.017766, 0.014489, 0.010501, 0.009333, 0.008662, 0.012657, 0.013541, 0.013743, 0.012099, 0.008626, 0.003764, 0.002923, 0.003599, 0.008197, 0.012315, 0.019187, 0.027514, 0.032284, 0.035808, 0.043728, 0.044926, 0.041041, 0.035530, 0.031913, 0.031121, 0.034344
|
|
#*# 0.019728, 0.022736, 0.020718, 0.022711, 0.022724, 0.017451, 0.013291, 0.011269, 0.013056, 0.018033, 0.019375, 0.018017, 0.014661, 0.013341, 0.009765, 0.008725, 0.008786, 0.013342, 0.019758, 0.027367, 0.034430, 0.041115, 0.045486, 0.045994, 0.043714, 0.040184, 0.036472, 0.036091, 0.036043, 0.040199
|
|
#*# 0.022780, 0.025036, 0.026834, 0.027283, 0.026190, 0.019616, 0.015740, 0.017856, 0.020673, 0.027386, 0.026210, 0.022030, 0.018611, 0.017350, 0.013559, 0.014168, 0.013241, 0.017310, 0.026426, 0.032507, 0.040918, 0.045681, 0.048944, 0.045972, 0.047095, 0.045990, 0.036709, 0.040476, 0.042475, 0.043938
|
|
#*# 0.022722, 0.027348, 0.028250, 0.031689, 0.029342, 0.022702, 0.018041, 0.022681, 0.027283, 0.031964, 0.030628, 0.023567, 0.021788, 0.019942, 0.017159, 0.013343, 0.013323, 0.018006, 0.027383, 0.036326, 0.043374, 0.046932, 0.048323, 0.049240, 0.046602, 0.045114, 0.044730, 0.045991, 0.048528, 0.050011
|
|
#*# 0.017921, 0.023267, 0.027424, 0.030234, 0.027547, 0.022625, 0.018068, 0.022400, 0.027180, 0.029568, 0.027399, 0.023128, 0.018247, 0.015692, 0.013348, 0.011055, 0.010999, 0.017145, 0.025021, 0.032611, 0.039029, 0.041349, 0.043816, 0.050322, 0.048384, 0.046153, 0.050641, 0.049355, 0.048305, 0.051019
|
|
#*# 0.018032, 0.022729, 0.022743, 0.026720, 0.022859, 0.018039, 0.018009, 0.018702, 0.023635, 0.025576, 0.024100, 0.019126, 0.015408, 0.011222, 0.008596, 0.007807, 0.008276, 0.013443, 0.022513, 0.030282, 0.037635, 0.039238, 0.043148, 0.046236, 0.048911, 0.050622, 0.051058, 0.050178, 0.047745, 0.050304
|
|
#*# 0.029015, 0.026504, 0.027418, 0.023701, 0.022682, 0.017925, 0.017749, 0.019914, 0.022718, 0.022731, 0.022055, 0.016786, 0.013316, 0.012432, 0.008648, 0.005006, 0.006292, 0.013146, 0.022904, 0.032159, 0.039122, 0.041428, 0.045999, 0.050383, 0.052283, 0.051744, 0.050801, 0.049593, 0.048787, 0.050479
|
|
#*# 0.033720, 0.031918, 0.030671, 0.027373, 0.022062, 0.018007, 0.018033, 0.020072, 0.022843, 0.022712, 0.020209, 0.015764, 0.015199, 0.012316, 0.008772, 0.007223, 0.006219, 0.012486, 0.022263, 0.031719, 0.036682, 0.041234, 0.045921, 0.051163, 0.054236, 0.052916, 0.049491, 0.046008, 0.046519, 0.047990
|
|
#*# 0.040185, 0.036667, 0.036572, 0.032686, 0.027416, 0.023039, 0.022750, 0.026763, 0.027358, 0.027591, 0.024049, 0.021739, 0.018043, 0.017108, 0.014281, 0.008581, 0.008439, 0.013342, 0.020976, 0.031636, 0.040911, 0.044845, 0.050569, 0.055101, 0.055645, 0.055290, 0.050786, 0.047153, 0.047547, 0.049529
|
|
#*# 0.050799, 0.050477, 0.048884, 0.045049, 0.039163, 0.034192, 0.032615, 0.035496, 0.036833, 0.040107, 0.037067, 0.033980, 0.031965, 0.027724, 0.027340, 0.023515, 0.022705, 0.026745, 0.034204, 0.041362, 0.049595, 0.057520, 0.064449, 0.069126, 0.069072, 0.069053, 0.064433, 0.059875, 0.059831, 0.060199
|
|
#*# 0.063424, 0.060147, 0.056388, 0.054858, 0.050246, 0.045998, 0.045942, 0.045994, 0.047875, 0.050295, 0.047217, 0.044659, 0.041465, 0.040757, 0.039453, 0.036354, 0.035854, 0.038856, 0.045450, 0.053001, 0.062335, 0.069524, 0.074049, 0.078365, 0.078384, 0.078263, 0.074234, 0.070780, 0.073069, 0.073252
|
|
#*# x_count = 30
|
|
#*# y_count = 30
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*# min_x = 30.0
|
|
#*# max_x = 310.0
|
|
#*# min_y = 30.0
|
|
#*# max_y = 310.0
|