514 lines
22 KiB
INI
514 lines
22 KiB
INI
# MMU to be disconnected, so let's have klipper able to run without it.
|
|
#[include mmu/base/*.cfg]
|
|
#[include mmu/optional/client_macros.cfg]
|
|
#[include mmu/optional/mmu_menu.cfg]
|
|
[include timelapse.cfg]
|
|
# This file contains common pin mappings for the BigTreeTech Octopus V1.
|
|
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
|
|
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
|
|
|
|
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
|
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] and [heater_bed] sections - See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types
|
|
## Z Endstop Switch location [safe_z_home] section
|
|
## Homing end position [gcode_macro G32] section
|
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
|
## Probe points [quad_gantry_level] section
|
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
|
## PID tune [extruder] and [heater_bed] sections
|
|
## Probe pin [probe] section
|
|
## Fine tune E steps [extruder] section
|
|
|
|
[mcu]
|
|
# katapulted klipper on can
|
|
canbus_uuid: 970febd72165
|
|
# katapulted klipper on usb
|
|
#serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_210044000150335331383520-if00
|
|
|
|
[include ebb36.cfg]
|
|
[include fluidd.cfg]
|
|
[include stealthburner_leds.cfg]
|
|
[include bedfans.cfg]
|
|
[include martyn_macros.cfg]
|
|
[include carto.cfg]
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 700
|
|
max_accel: 3300 #Max 4000
|
|
max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 350
|
|
square_corner_velocity: 5.0
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
## B Stepper - Left
|
|
## Connected to MOTOR_0
|
|
## Endstop connected to DIAG_0
|
|
[stepper_x]
|
|
step_pin: PF13
|
|
dir_pin: PF12
|
|
enable_pin: !PF14
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 200 for 1.8 degree stepper
|
|
endstop_pin: PG6
|
|
position_min: 0
|
|
position_endstop: 345
|
|
position_max: 345
|
|
homing_speed: 70 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC4
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## A Stepper - Right
|
|
## Connected to MOTOR_1
|
|
## Endstop connected to DIAG_1
|
|
[stepper_y]
|
|
step_pin: PG0
|
|
dir_pin: PG1
|
|
enable_pin: !PF15
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 200 for 1.8 degree stepper
|
|
endstop_pin: PG9
|
|
position_min: 0
|
|
position_endstop: 355
|
|
position_max: 355
|
|
homing_speed: 70 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PD11
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## Z0 Stepper - Front Left
|
|
## Connected to MOTOR_2
|
|
## Endstop connected to DIAG_2
|
|
[stepper_z]
|
|
step_pin: PF11
|
|
dir_pin: PG3
|
|
enable_pin: !PG5
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
endstop_pin: probe:z_virtual_endstop
|
|
#endstop_pin: !ebb36:PB7
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
#position_endstop: 0
|
|
position_max: 310
|
|
position_min: -5
|
|
homing_speed: 15
|
|
#second_homing_speed: 3
|
|
#homing_retract_dist: 3
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC6
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z1 Stepper - Rear Left
|
|
## Connected to MOTOR_3
|
|
[stepper_z1]
|
|
step_pin: PG4
|
|
dir_pin: !PC1
|
|
enable_pin: !PA0
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PC7
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z2 Stepper - Rear Right
|
|
## Connected to MOTOR_4
|
|
[stepper_z2]
|
|
step_pin: PF9
|
|
dir_pin: PF10
|
|
enable_pin: !PG2
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PF2
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
## Z3 Stepper - Front Right
|
|
## Connected to MOTOR_5
|
|
[stepper_z3]
|
|
step_pin: PC13
|
|
dir_pin: !PF0
|
|
enable_pin: !PF1
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PE4
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 999999
|
|
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
|
|
## SSR Pin - HE1
|
|
## Thermistor - TB
|
|
[heater_bed]
|
|
heater_pin: PA1
|
|
## Validate the following thermistor type to make sure it is correct
|
|
## Keenovo branded bed heaters should use Generic 3950
|
|
## LDO branded bed heaters will have the sensor type labelled on the heater
|
|
## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types.
|
|
## Use "Generic 3950" for Keenovo heaters
|
|
sensor_type: ATC Semitec 104NT-4-R025H42G
|
|
sensor_pin: PF3
|
|
## Adjust Max Power so your heater doesn't warp your bed. Rule of thumb is 0.4 watts / cm^2 .
|
|
max_power: 0.6
|
|
min_temp: 0
|
|
max_temp: 120
|
|
control: pid
|
|
pid_Kp: 43.209
|
|
pid_Ki: 1.162
|
|
pid_Kd: 401.841
|
|
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
|
|
|
|
## Controller fan - FAN2
|
|
[temperature_fan controller_fan]
|
|
pin: PD12
|
|
sensor_type: temperature_host
|
|
control: watermark
|
|
max_delta: 3
|
|
min_temp: 0
|
|
max_temp: 100
|
|
target_temp: 55
|
|
max_speed: 0.5
|
|
|
|
## Exhaust fan - FAN3
|
|
#[heater_fan exhaust_fan]
|
|
#pin: PD13
|
|
#max_power: 1.0
|
|
#shutdown_speed: 0.0
|
|
#kick_start_time: 5.0
|
|
#heater: heater_bed
|
|
#heater_temp: 60
|
|
#fan_speed: 1.0
|
|
|
|
#####################################################################
|
|
# LED Control
|
|
#####################################################################
|
|
|
|
[output_pin caselight]
|
|
## Chamber Lighting - CNC_FAN5
|
|
pin: PD15
|
|
pwm:true
|
|
shutdown_value: 0
|
|
value:1
|
|
cycle_time: 0.01
|
|
|
|
#####################################################################
|
|
# Additional Sensors
|
|
#####################################################################
|
|
|
|
[thermistor CMFB103F3950FANT]
|
|
temperature1: 0.0
|
|
resistance1: 32116.0
|
|
temperature2: 40.0
|
|
resistance2: 5309.0
|
|
temperature3: 80.0
|
|
resistance3: 1228.0
|
|
|
|
[temperature_sensor chamber_temp]
|
|
# Chamber Temperature - T1
|
|
sensor_type: EPCOS 100K B57560G104F # total guess really, but sure.
|
|
sensor_pin: PF5
|
|
min_temp: 0
|
|
max_temp: 100
|
|
gcode_id: chamber_th
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
timeout: 1800
|
|
|
|
# Need to work out how eddy interferes with magic home
|
|
#[safe_z_home]
|
|
#home_xy_position: 175,175
|
|
#speed:100
|
|
#z_hop:10
|
|
#z_hop_speed:10
|
|
|
|
[homing_override]
|
|
axes: z
|
|
gcode:
|
|
SET_KINEMATIC_POSITION Z=0
|
|
G1 Z10 F3000
|
|
{% if not 'X' in printer.toolhead.homed_axes %}
|
|
G28 X0
|
|
{% endif %}
|
|
{% if not 'Y' in printer.toolhead.homed_axes %}
|
|
G28 Y0
|
|
{% endif %}
|
|
G1 X150 Y150 F3000
|
|
G28 Z0
|
|
G1 Z10 F3000
|
|
|
|
|
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
|
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
|
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
|
## to respective belt positions
|
|
[quad_gantry_level]
|
|
gantry_corners:
|
|
-60,-10
|
|
410,420
|
|
# Probe points
|
|
points:
|
|
50,25
|
|
50,275
|
|
300,275
|
|
300,25
|
|
|
|
speed: 100
|
|
horizontal_move_z: 2
|
|
retries: 5
|
|
retry_tolerance: 0.04
|
|
max_adjust: 10
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PE8, EXP1_2=PE7,
|
|
EXP1_3=PE9, EXP1_4=PE10,
|
|
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
|
|
EXP1_7=PE14, EXP1_8=PE15,
|
|
EXP1_9=<GND>, EXP1_10=<5V>,
|
|
|
|
# EXP2 header
|
|
EXP2_1=PA6, EXP2_2=PA5,
|
|
EXP2_3=PB1, EXP2_4=PA4,
|
|
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
|
|
EXP2_7=PC15, EXP2_8=<RST>,
|
|
EXP2_9=<GND>, EXP2_10=<5V>
|
|
|
|
#####################################################################
|
|
# Displays
|
|
#####################################################################
|
|
|
|
[display]
|
|
# mini12864 LCD Display
|
|
lcd_type: uc1701
|
|
cs_pin: EXP1_3
|
|
a0_pin: EXP1_4
|
|
rst_pin: EXP1_5
|
|
encoder_pins: ^EXP2_5, ^EXP2_3
|
|
click_pin: ^!EXP1_2
|
|
contrast: 63
|
|
spi_software_miso_pin: EXP2_1
|
|
spi_software_mosi_pin: EXP2_6
|
|
spi_software_sclk_pin: EXP2_2
|
|
|
|
[neopixel btt_mini12864]
|
|
# To control Neopixel RGB in mini12864 display
|
|
pin: EXP1_6
|
|
chain_count: 3
|
|
initial_RED: 0.6
|
|
initial_GREEN: 0.0
|
|
initial_BLUE: 0.0
|
|
color_order: RGB
|
|
|
|
## Set RGB values on boot up for each Neopixel.
|
|
## Index 1 = display, Index 2 and 3 = Knob
|
|
[delayed_gcode setdisplayneopixel]
|
|
initial_duration: 1
|
|
gcode:
|
|
SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=0.6 GREEN=0 BLUE=1 INDEX=2 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=0.6 GREEN=0 BLUE=1 INDEX=3
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
[temperature_sensor pi]
|
|
sensor_type: temperature_host
|
|
|
|
[temperature_sensor mcu]
|
|
sensor_type: temperature_mcu
|
|
|
|
[skew_correction]
|
|
|
|
[exclude_object]
|
|
|
|
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
|
|
#[probe] ## Other parameters in config.cfg
|
|
#pin: !ebb36:PB7
|
|
#x_offset: 0.0
|
|
#y_offset: 0.0
|
|
#z_offset: 0.0
|
|
#speed: 15.0 # Speed (in mm/s) of the Z axis when probing. The default is 5mm/s.
|
|
#samples: 2
|
|
#sample_retract_dist: 3.0
|
|
#samples_tolerance_retries: 1
|
|
#lift_speed: 10
|
|
#activate_gcode:
|
|
# G4 P200 ;Wait 200ms
|
|
# SET_TMC_CURRENT STEPPER=stepper_z CURRENT=0.4
|
|
# SET_TMC_CURRENT STEPPER=stepper_z1 CURRENT=0.4
|
|
# SET_TMC_CURRENT STEPPER=stepper_z2 CURRENT=0.4
|
|
# SET_TMC_CURRENT STEPPER=stepper_z3 CURRENT=0.4
|
|
#deactivate_gcode:
|
|
# {% set run_current = printer.configfile.config['tmc2209 stepper_z'].run_current | float %}
|
|
# SET_TMC_CURRENT STEPPER=stepper_z CURRENT={run_current}
|
|
# SET_TMC_CURRENT STEPPER=stepper_z1 CURRENT={run_current}
|
|
# SET_TMC_CURRENT STEPPER=stepper_z2 CURRENT={run_current}
|
|
# SET_TMC_CURRENT STEPPER=stepper_z3 CURRENT={run_current}
|
|
|
|
[input_shaper]
|
|
shaper_freq_x: 91.4
|
|
shaper_freq_y: 70.0
|
|
shaper_type: 3hump_ei
|
|
|
|
[force_move]
|
|
enable_force_move: True
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [skew_correction calilantern_skew_profile]
|
|
#*# xy_skew = 0.002269819397871509
|
|
#*# xz_skew = 0.0
|
|
#*# yz_skew = 0.0
|
|
#*#
|
|
#*# [scanner]
|
|
#*# mode = touch
|
|
#*# scanner_touch_threshold = 750
|
|
#*# scanner_touch_speed = 2
|
|
#*# scanner_touch_z_offset = 0.100
|
|
#*#
|
|
#*# [scanner model default]
|
|
#*# model_coef = 1.54547696704748,
|
|
#*# 1.9826316137382953,
|
|
#*# 0.7339776131866772,
|
|
#*# 0.30422507330624265,
|
|
#*# 0.3176616902930693,
|
|
#*# 0.2617860932937524,
|
|
#*# -0.22258329370910082,
|
|
#*# -0.21919831625292302,
|
|
#*# 0.17974948476952415,
|
|
#*# 0.12614743068240433
|
|
#*# model_domain = 3.298780241186128e-07,3.347286858645663e-07
|
|
#*# model_range = 0.100000,5.000000
|
|
#*# model_temp = 41.081679
|
|
#*# model_offset = 0.00000
|
|
#*# model_mode = touch
|
|
#*# model_fw_version = CARTOGRAPHER 5.0.0
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.010341, 0.008043, 0.023238, 0.011449, -0.000044, 0.014696, 0.004508, -0.005732, 0.011335, 0.007902, 0.004316, 0.013196, 0.023752, 0.015810, 0.008264, 0.008183, 0.004417, 0.013600, 0.027388, 0.023790, 0.032159, 0.046991, 0.047951, 0.038473, 0.036008, 0.032597, 0.025730, 0.022583, 0.027525, 0.022414
|
|
#*# 0.020635, 0.018620, 0.008504, 0.013783, 0.020505, 0.018517, -0.002339, 0.003598, 0.014056, 0.008784, 0.009234, 0.013188, 0.014867, 0.013348, 0.005222, 0.018136, 0.008693, -0.000058, 0.018516, 0.037165, 0.030348, 0.034961, 0.052331, 0.040560, 0.036452, 0.022915, 0.027142, 0.022917, 0.021779, 0.041143
|
|
#*# 0.017261, 0.032589, 0.011510, 0.008616, 0.027478, 0.013798, 0.009731, 0.008680, 0.006857, 0.017797, 0.002883, 0.012021, 0.020655, 0.011493, 0.007917, -0.000296, -0.000858, 0.013775, 0.018136, 0.027489, 0.037905, 0.036886, 0.050540, 0.046823, 0.037247, 0.026527, 0.029202, 0.032249, 0.031802, 0.032123
|
|
#*# 0.030140, 0.018467, 0.026343, 0.025382, 0.028087, 0.018268, 0.008353, 0.004564, 0.011719, 0.023058, 0.015968, 0.008775, 0.015725, 0.022692, 0.018364, -0.004618, 0.004577, 0.008188, 0.024083, 0.018185, 0.029765, 0.045333, 0.043580, 0.052191, 0.040985, 0.027465, 0.022937, 0.030417, 0.037410, 0.046082
|
|
#*# 0.044863, 0.031046, 0.020655, 0.017438, 0.033175, 0.021101, 0.018529, 0.008069, 0.024190, 0.017356, 0.020184, 0.011483, 0.012636, 0.024012, 0.018380, 0.003703, 0.002274, 0.009592, 0.022622, 0.025373, 0.032032, 0.045606, 0.050884, 0.046251, 0.042060, 0.034338, 0.034897, 0.041193, 0.030322, 0.039636
|
|
#*# 0.041138, 0.026545, 0.029706, 0.027219, 0.029570, 0.027473, 0.009231, 0.014519, 0.016080, 0.024146, 0.013757, 0.013671, 0.020227, 0.023759, 0.014183, 0.004578, 0.011089, 0.010750, 0.023265, 0.028607, 0.026953, 0.043924, 0.050573, 0.050784, 0.036368, 0.032371, 0.035475, 0.043179, 0.031978, 0.039736
|
|
#*# 0.042113, 0.041144, 0.031389, 0.018363, 0.013776, 0.027528, 0.017936, 0.008073, 0.016226, 0.020202, 0.020755, 0.027469, 0.013442, 0.018366, 0.022954, 0.014575, 0.015782, 0.004576, 0.015573, 0.031087, 0.036261, 0.041118, 0.036834, 0.043947, 0.046235, 0.036485, 0.037170, 0.027496, 0.032585, 0.045403
|
|
#*# 0.034721, 0.030530, 0.029383, 0.018214, 0.027494, 0.025227, 0.016087, 0.008505, 0.018928, 0.024375, 0.013776, 0.018596, 0.017973, 0.016636, 0.015758, 0.014987, 0.009317, 0.002317, 0.022953, 0.032150, 0.026693, 0.032087, 0.044097, 0.054651, 0.036331, 0.044228, 0.039150, 0.045889, 0.041468, 0.027436
|
|
#*# 0.038284, 0.034615, 0.028921, 0.017531, 0.027607, 0.027499, 0.009215, 0.012300, 0.019295, 0.017919, 0.013722, 0.020435, 0.018872, 0.016629, 0.018671, 0.011574, 0.004425, 0.013780, 0.019165, 0.022958, 0.035078, 0.043071, 0.044445, 0.043576, 0.045692, 0.036740, 0.034356, 0.038927, 0.031929, 0.034907
|
|
#*# 0.036681, 0.032136, 0.027089, 0.022907, 0.018448, 0.017305, 0.013844, 0.015949, 0.009723, 0.008355, 0.018705, 0.016571, 0.008652, 0.014912, 0.008606, 0.000005, 0.009183, 0.003979, 0.004543, 0.027500, 0.031883, 0.038631, 0.046603, 0.039108, 0.031935, 0.045776, 0.041545, 0.022271, 0.025930, 0.034854
|
|
#*# 0.041419, 0.022542, 0.032212, 0.021009, 0.016572, 0.013686, 0.009886, 0.006313, 0.004696, 0.007055, 0.009488, 0.004528, 0.008831, 0.009200, -0.004608, -0.000019, 0.000787, -0.004939, 0.003496, 0.018369, 0.025100, 0.027338, 0.032352, 0.029962, 0.031425, 0.029780, 0.025508, 0.022113, 0.021199, 0.031664
|
|
#*# 0.026335, 0.022263, 0.027540, 0.020100, 0.014996, 0.008072, 0.006869, 0.004190, 0.001431, 0.004699, 0.006617, 0.005204, 0.003428, 0.002362, 0.000007, -0.001592, -0.004649, 0.000209, 0.002401, 0.008038, 0.017547, 0.033103, 0.028064, 0.027581, 0.028689, 0.027457, 0.024188, 0.021559, 0.020761, 0.018543
|
|
#*# 0.036466, 0.024047, 0.013769, 0.017224, 0.013991, 0.010312, 0.006300, 0.002439, 0.002214, -0.000119, 0.004645, 0.008728, 0.001703, -0.004609, 0.001067, -0.002032, -0.000030, -0.006564, 0.002624, 0.011244, 0.022826, 0.022944, 0.025235, 0.025239, 0.027436, 0.022637, 0.018364, 0.019366, 0.019509, 0.025154
|
|
#*# 0.022630, 0.016359, 0.016281, 0.015625, 0.014908, 0.008796, 0.006606, 0.002419, 0.004888, 0.003472, 0.004474, 0.002390, 0.001694, -0.000985, -0.004884, -0.000423, -0.002864, 0.004578, 0.004018, 0.010240, 0.018397, 0.028331, 0.027740, 0.018052, 0.017505, 0.029803, 0.027558, 0.009354, 0.009163, 0.024621
|
|
#*# 0.023055, 0.013763, 0.016191, 0.018520, 0.016256, 0.007191, 0.003804, 0.002593, 0.005452, 0.004592, 0.005877, -0.001162, 0.001693, 0.002177, 0.000552, -0.002441, -0.002425, -0.002266, 0.004575, 0.004647, 0.016075, 0.022599, 0.021950, 0.023072, 0.021902, 0.022113, 0.021046, 0.019474, 0.015114, 0.019545
|
|
#*# 0.024957, 0.016097, 0.016634, 0.015839, 0.014317, 0.011241, 0.009695, 0.006842, 0.009378, 0.009200, 0.006907, 0.006995, 0.005504, 0.005702, 0.003452, 0.002527, 0.000698, 0.004778, 0.009522, 0.008376, 0.016187, 0.024008, 0.028093, 0.026360, 0.022901, 0.029636, 0.027208, 0.027689, 0.013669, 0.018297
|
|
#*# 0.032365, 0.027637, 0.018452, 0.013784, 0.013362, 0.018364, 0.011309, 0.011019, 0.011213, 0.009309, 0.012083, 0.014329, 0.011493, 0.009167, 0.009758, 0.007995, 0.006641, 0.003760, 0.011359, 0.015605, 0.023472, 0.029773, 0.030906, 0.030212, 0.033008, 0.031163, 0.027520, 0.028117, 0.024953, 0.027923
|
|
#*# 0.028776, 0.024749, 0.021082, 0.023690, 0.020507, 0.013797, 0.011694, 0.011233, 0.015545, 0.013555, 0.013060, 0.020468, 0.016194, 0.013911, 0.012396, 0.010071, 0.008777, 0.009500, 0.018365, 0.013529, 0.032500, 0.037714, 0.034366, 0.027523, 0.041611, 0.036447, 0.034223, 0.031517, 0.025454, 0.029852
|
|
#*# 0.036597, 0.022464, 0.018310, 0.023078, 0.018652, 0.012640, 0.009760, 0.018292, 0.018364, 0.017261, 0.013816, 0.022944, 0.020653, 0.016064, 0.013088, 0.013779, 0.007235, 0.006985, 0.013261, 0.018678, 0.027420, 0.032804, 0.034491, 0.034315, 0.034138, 0.034261, 0.031460, 0.028088, 0.023376, 0.027499
|
|
#*# 0.035267, 0.027551, 0.023341, 0.021950, 0.021163, 0.019357, 0.017237, 0.016086, 0.018649, 0.024054, 0.027156, 0.028499, 0.028029, 0.023172, 0.020331, 0.016088, 0.011574, 0.008609, 0.018369, 0.021853, 0.027454, 0.038375, 0.041211, 0.036637, 0.038076, 0.033889, 0.032380, 0.025953, 0.022869, 0.026369
|
|
#*# 0.040216, 0.027505, 0.022623, 0.025217, 0.024247, 0.024638, 0.021128, 0.020823, 0.023552, 0.033918, 0.034057, 0.031983, 0.033042, 0.028661, 0.022289, 0.018350, 0.014350, 0.013770, 0.018664, 0.026832, 0.032107, 0.036746, 0.045676, 0.039006, 0.036150, 0.034334, 0.032491, 0.027393, 0.027494, 0.031144
|
|
#*# 0.039364, 0.031551, 0.024088, 0.027499, 0.025247, 0.025611, 0.025683, 0.031188, 0.034167, 0.036394, 0.039250, 0.038429, 0.036590, 0.027731, 0.020672, 0.018340, 0.018364, 0.011305, 0.013469, 0.024664, 0.029788, 0.046718, 0.046216, 0.031786, 0.033181, 0.037102, 0.031562, 0.027862, 0.027763, 0.027062
|
|
#*# 0.041473, 0.028132, 0.020657, 0.020666, 0.021956, 0.024012, 0.022994, 0.026580, 0.032029, 0.037749, 0.037769, 0.032082, 0.026499, 0.022490, 0.018336, 0.011807, 0.008091, 0.007345, 0.013783, 0.022937, 0.030189, 0.035946, 0.036134, 0.032367, 0.032058, 0.031006, 0.029867, 0.028654, 0.028062, 0.034616
|
|
#*# 0.054672, 0.033056, 0.022801, 0.020809, 0.022299, 0.022959, 0.026216, 0.027642, 0.032349, 0.036178, 0.036031, 0.031402, 0.022939, 0.018287, 0.012682, 0.009016, 0.005235, 0.008086, 0.013764, 0.022636, 0.031087, 0.036713, 0.036307, 0.034074, 0.032610, 0.035510, 0.034756, 0.034113, 0.031692, 0.036789
|
|
#*# 0.072186, 0.041971, 0.026016, 0.020093, 0.020077, 0.022948, 0.023118, 0.026718, 0.028132, 0.031797, 0.031986, 0.026956, 0.018766, 0.013478, 0.009187, 0.007326, 0.005060, 0.009192, 0.015077, 0.024528, 0.032206, 0.036907, 0.037782, 0.036822, 0.037053, 0.040243, 0.039830, 0.036692, 0.034133, 0.040334
|
|
#*# 0.085211, 0.047736, 0.027476, 0.018425, 0.019078, 0.018675, 0.018957, 0.021185, 0.022944, 0.027533, 0.027471, 0.022835, 0.018114, 0.011646, 0.009020, 0.004554, 0.004570, 0.009344, 0.014817, 0.022873, 0.032567, 0.036934, 0.038882, 0.037061, 0.037778, 0.040966, 0.041266, 0.036498, 0.032085, 0.041315
|
|
#*# 0.086287, 0.045480, 0.022907, 0.013793, 0.013490, 0.011870, 0.011266, 0.012612, 0.015752, 0.018404, 0.019013, 0.017462, 0.011573, 0.006915, 0.003708, 0.001711, 0.000005, 0.002345, 0.007941, 0.016053, 0.023655, 0.029766, 0.032053, 0.032769, 0.033084, 0.032079, 0.031731, 0.027404, 0.027290, 0.033173
|
|
#*# 0.077876, 0.038749, 0.017756, 0.009415, 0.009003, 0.008192, 0.007362, 0.004755, 0.009133, 0.013766, 0.015004, 0.013786, 0.009774, 0.004500, -0.000020, -0.002350, -0.002697, -0.002557, 0.002205, 0.009223, 0.018324, 0.022978, 0.027551, 0.030200, 0.031082, 0.029896, 0.027797, 0.023730, 0.022936, 0.029789
|
|
#*# 0.061804, 0.031407, 0.013609, 0.005822, 0.004726, 0.004321, 0.003003, 0.002613, 0.004625, 0.009263, 0.013510, 0.011781, 0.006241, 0.002098, -0.001477, -0.004332, -0.004655, -0.004667, -0.001018, 0.006865, 0.015949, 0.024355, 0.027509, 0.028506, 0.030481, 0.030868, 0.027486, 0.022928, 0.022753, 0.029223
|
|
#*# 0.050383, 0.023414, 0.011332, 0.006716, 0.004629, 0.004517, 0.004058, 0.003221, 0.004902, 0.009303, 0.013768, 0.011742, 0.008608, 0.003676, -0.000416, -0.003623, -0.004613, -0.004612, 0.000026, 0.009219, 0.018389, 0.023926, 0.027525, 0.027547, 0.028451, 0.027514, 0.026614, 0.022910, 0.023165, 0.030379
|
|
#*# x_count = 30
|
|
#*# y_count = 30
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*# min_x = 30.0
|
|
#*# max_x = 310.0
|
|
#*# min_y = 30.0
|
|
#*# max_y = 310.0
|
|
#*#
|
|
#*# [skew_correction Calilantern]
|
|
#*# xy_skew = 0.0004221439779203628
|
|
#*# xz_skew = 0.0
|
|
#*# yz_skew = 0.0
|