[mcu ebb36]
canbus_uuid: 856855c0f065

[temperature_sensor ebb36]
sensor_type: temperature_mcu
sensor_mcu: ebb36
min_temp: 0
max_temp: 100

[adxl345]
cs_pin: ebb36: PB12
spi_software_sclk_pin: ebb36: PB10
spi_software_mosi_pin: ebb36: PB11
spi_software_miso_pin: ebb36: PB2
axes_map: x,y,z

#####################################################################
#   Extruder
#####################################################################

##  Connected to MOTOR_6
##  Heater - HE0
##  Thermistor - T0
[extruder]
step_pin: ebb36: PD0
dir_pin: ebb36: PD1
enable_pin: !ebb36: PD2
##  Update value below when you perform extruder calibration
##  If you ask for 100mm of filament, but in reality it is 98mm:
##  rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
##  22.6789511 is a good starting point
#rotation_distance: 22.6789511   #Bondtech 5mm Drive Gears
# 101/100
rotation_distance: 22.905740611
##  Update Gear Ratio depending on your Extruder Type
##  Use 50:10 for Stealthburner/Clockwork 2
##  Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
##  Use 80:20 for M4, M3.1
gear_ratio: 50:10               #BMG Gear Ratio
microsteps: 16
full_steps_per_rotation: 200    #200 for 1.8 degree, 400 for 0.9 degree
nozzle_diameter: 0.400
filament_diameter: 1.75
heater_pin: ebb36: PB13
## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types.
## Use "Generic 3950" for NTC 100k 3950 thermistors
sensor_type: ATC Semitec 104NT-4-R025H42G
sensor_pin: ebb36: PA3
min_temp: 10
max_temp: 295
max_power: 1.0
min_extrude_temp: 170
control = pid
pid_kp = 26.213
pid_ki = 1.304
pid_kd = 131.721
max_extrude_only_distance = 101
##  Try to keep pressure_advance below 1.0
#pressure_advance: 0.05
##  Default is 0.040, leave stock
#pressure_advance_smooth_time: 0.040

##  E0 on MOTOR6
##  Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 extruder]
uart_pin: ebb36: PA15
interpolate: false
run_current: 0.5
sense_resistor: 0.110
stealthchop_threshold: 0

[fan]
kick_start_time: 0.5
pin: ebb36: PA1

[heater_fan hotend_fan]
pin: ebb36: PA0
max_power: 1.0
kick_start_time: 0.5
heater: extruder
heater_temp: 50.0
##  If you are experiencing back flow, you can reduce fan_speed
#fan_speed: 1.0

[neopixel sb_leds]
pin: ebb36:PD3
chain_count: 3
#   The number of Neopixel chips that are "daisy chained" to the
#   provided pin. The default is 1 (which indicates only a single
#   Neopixel is connected to the pin).
color_order: GRBW
#   Set the pixel order required by the LED hardware. Options are GRB,
#   RGB, GRBW, or RGBW. The default is GRB.
initial_RED: 0.0
initial_GREEN: 0.0
initial_BLUE: 0.0
initial_WHITE: 0.0

#####################################################################
#   Probe
#####################################################################

##  Inductive Probe
##  This probe is not used for Z height, only Quad Gantry Leveling
# moved to printer.cfg so I can save from the interface.
# [probe]
# pin: ebb36:PB8
# x_offset: 0
# y_offset: 19.75
# z_offset: 5.930
# # below is default, trying -0.365 measured, if +0.365, it's 6.785
# # z_offset: 6.42
# speed: 5
# samples: 3
# samples_result: median
# sample_retract_dist: 2.0
# samples_tolerance: 0.01
# samples_tolerance_retries: 3

[adxl345]
cs_pin: ebb36:PB12
spi_software_sclk_pin: ebb36:PB10
spi_software_mosi_pin: ebb36:PB11
spi_software_miso_pin: ebb36:PB2
axes_map: x,y,z

[resonance_tester]
accel_chip: adxl345
probe_points: 175,175,15