[include mmu/base/*.cfg] [include mmu/optional/client_macros.cfg] [include mmu/optional/mmu_menu.cfg] [include timelapse.cfg] # This file contains common pin mappings for the BigTreeTech Octopus V1. # To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader" # Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference # after running "make", copy the generated "klipper/out/klipper.bin" file to a # file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card. # See docs/Config_Reference.md for a description of parameters. ## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config ## *** THINGS TO CHANGE/CHECK: *** ## MCU paths [mcu] section ## Thermistor types [extruder] and [heater_bed] sections - See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types ## Z Endstop Switch location [safe_z_home] section ## Homing end position [gcode_macro G32] section ## Z Endstop Switch offset for Z0 [stepper_z] section ## Probe points [quad_gantry_level] section ## Min & Max gantry corner postions [quad_gantry_level] section ## PID tune [extruder] and [heater_bed] sections ## Probe pin [probe] section ## Fine tune E steps [extruder] section [mcu] # katapulted klipper on can canbus_uuid: 970febd72165 # katapulted klipper on usb #serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_210044000150335331383520-if00 [include ebb36.cfg] [include fluidd.cfg] [include stealthburner_leds.cfg] [include bedfans.cfg] [include martyn_macros.cfg] [include carto.cfg] [printer] kinematics: corexy max_velocity: 700 max_accel: 3300 #Max 4000 max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V max_z_accel: 350 square_corner_velocity: 5.0 ##################################################################### # X/Y Stepper Settings ##################################################################### ## B Stepper - Left ## Connected to MOTOR_0 ## Endstop connected to DIAG_0 [stepper_x] step_pin: PF13 dir_pin: PF12 enable_pin: !PF14 rotation_distance: 40 microsteps: 32 full_steps_per_rotation:400 #set to 200 for 1.8 degree stepper endstop_pin: PG6 position_min: 0 position_endstop: 345 position_max: 345 homing_speed: 70 #Max 100 homing_retract_dist: 5 homing_positive_dir: true ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_x] uart_pin: PC4 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## A Stepper - Right ## Connected to MOTOR_1 ## Endstop connected to DIAG_1 [stepper_y] step_pin: PG0 dir_pin: PG1 enable_pin: !PF15 rotation_distance: 40 microsteps: 32 full_steps_per_rotation:400 #set to 200 for 1.8 degree stepper endstop_pin: PG9 position_min: 0 position_endstop: 355 position_max: 355 homing_speed: 70 #Max 100 homing_retract_dist: 5 homing_positive_dir: true ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_y] uart_pin: PD11 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ##################################################################### # Z Stepper Settings ##################################################################### ## Z0 Stepper - Front Left ## Connected to MOTOR_2 ## Endstop connected to DIAG_2 [stepper_z] step_pin: PF11 dir_pin: PG3 enable_pin: !PG5 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 endstop_pin: probe:z_virtual_endstop #endstop_pin: !ebb36:PB7 ## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) ## (+) value = endstop above Z0, (-) value = endstop below ## Increasing position_endstop brings nozzle closer to the bed ## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config #position_endstop: 0 position_max: 310 position_min: -5 homing_speed: 15 #second_homing_speed: 3 #homing_retract_dist: 3 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z] uart_pin: PC6 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 999999 ## Z1 Stepper - Rear Left ## Connected to MOTOR_3 [stepper_z1] step_pin: PG4 dir_pin: !PC1 enable_pin: !PA0 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z1] uart_pin: PC7 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 999999 ## Z2 Stepper - Rear Right ## Connected to MOTOR_4 [stepper_z2] step_pin: PF9 dir_pin: PF10 enable_pin: !PG2 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z2] uart_pin: PF2 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 999999 ## Z3 Stepper - Front Right ## Connected to MOTOR_5 [stepper_z3] step_pin: PC13 dir_pin: !PF0 enable_pin: !PF1 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z3] uart_pin: PE4 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 999999 ##################################################################### # Bed Heater ##################################################################### ## SSR Pin - HE1 ## Thermistor - TB [heater_bed] heater_pin: PA1 ## Validate the following thermistor type to make sure it is correct ## Keenovo branded bed heaters should use Generic 3950 ## LDO branded bed heaters will have the sensor type labelled on the heater ## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types. ## Use "Generic 3950" for Keenovo heaters sensor_type: ATC Semitec 104NT-4-R025H42G sensor_pin: PF3 ## Adjust Max Power so your heater doesn't warp your bed. Rule of thumb is 0.4 watts / cm^2 . max_power: 0.6 min_temp: 0 max_temp: 120 control: pid pid_Kp: 43.209 pid_Ki: 1.162 pid_Kd: 401.841 ##################################################################### # Fan Control ##################################################################### ## Controller fan - FAN2 [temperature_fan controller_fan] pin: PD12 sensor_type: temperature_host control: watermark max_delta: 3 min_temp: 0 max_temp: 100 target_temp: 55 max_speed: 0.5 ## Exhaust fan - FAN3 #[heater_fan exhaust_fan] #pin: PD13 #max_power: 1.0 #shutdown_speed: 0.0 #kick_start_time: 5.0 #heater: heater_bed #heater_temp: 60 #fan_speed: 1.0 ##################################################################### # LED Control ##################################################################### [output_pin caselight] ## Chamber Lighting - CNC_FAN5 pin: PD15 pwm:true shutdown_value: 0 value:1 cycle_time: 0.01 ##################################################################### # Additional Sensors ##################################################################### [thermistor CMFB103F3950FANT] temperature1: 0.0 resistance1: 32116.0 temperature2: 40.0 resistance2: 5309.0 temperature3: 80.0 resistance3: 1228.0 [temperature_sensor chamber_temp] # Chamber Temperature - T1 sensor_type: EPCOS 100K B57560G104F # total guess really, but sure. sensor_pin: PF5 min_temp: 0 max_temp: 100 gcode_id: chamber_th ##################################################################### # Homing and Gantry Adjustment Routines ##################################################################### [idle_timeout] timeout: 1800 # Need to work out how eddy interferes with magic home #[safe_z_home] #home_xy_position: 175,175 #speed:100 #z_hop:10 #z_hop_speed:10 [homing_override] axes: z gcode: SET_KINEMATIC_POSITION Z=0 G1 Z10 F3000 {% if not 'X' in printer.toolhead.homed_axes %} G28 X0 {% endif %} {% if not 'Y' in printer.toolhead.homed_axes %} G28 Y0 {% endif %} G1 X150 Y150 F3000 G28 Z0 G1 Z10 F3000 ## Use QUAD_GANTRY_LEVEL to level a gantry. ## Min & Max gantry corners - measure from nozzle at MIN (0,0) and ## MAX (250, 250), (300,300), or (350,350) depending on your printer size ## to respective belt positions [quad_gantry_level] gantry_corners: -60,-10 410,420 # Probe points points: 50,25 50,275 300,275 300,25 speed: 100 horizontal_move_z: 2 retries: 5 retry_tolerance: 0.04 max_adjust: 10 ######################################## # EXP1 / EXP2 (display) pins ######################################## [board_pins] aliases: # EXP1 header EXP1_1=PE8, EXP1_2=PE7, EXP1_3=PE9, EXP1_4=PE10, EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side EXP1_7=PE14, EXP1_8=PE15, EXP1_9=, EXP1_10=<5V>, # EXP2 header EXP2_1=PA6, EXP2_2=PA5, EXP2_3=PB1, EXP2_4=PA4, EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side EXP2_7=PC15, EXP2_8=, EXP2_9=, EXP2_10=<5V> ##################################################################### # Displays ##################################################################### [display] # mini12864 LCD Display lcd_type: uc1701 cs_pin: EXP1_3 a0_pin: EXP1_4 rst_pin: EXP1_5 encoder_pins: ^EXP2_5, ^EXP2_3 click_pin: ^!EXP1_2 contrast: 63 spi_software_miso_pin: EXP2_1 spi_software_mosi_pin: EXP2_6 spi_software_sclk_pin: EXP2_2 [neopixel btt_mini12864] # To control Neopixel RGB in mini12864 display pin: EXP1_6 chain_count: 3 initial_RED: 0.6 initial_GREEN: 0.0 initial_BLUE: 0.0 color_order: RGB ## Set RGB values on boot up for each Neopixel. ## Index 1 = display, Index 2 and 3 = Knob [delayed_gcode setdisplayneopixel] initial_duration: 1 gcode: SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 SET_LED LED=btt_mini12864 RED=0.6 GREEN=0 BLUE=1 INDEX=2 TRANSMIT=0 SET_LED LED=btt_mini12864 RED=0.6 GREEN=0 BLUE=1 INDEX=3 #-------------------------------------------------------------------- [temperature_sensor pi] sensor_type: temperature_host [temperature_sensor mcu] sensor_type: temperature_mcu [skew_correction] [exclude_object] ##################################################################### # Macros ##################################################################### #[probe] ## Other parameters in config.cfg #pin: !ebb36:PB7 #x_offset: 0.0 #y_offset: 0.0 #z_offset: 0.0 #speed: 15.0 # Speed (in mm/s) of the Z axis when probing. The default is 5mm/s. #samples: 2 #sample_retract_dist: 3.0 #samples_tolerance_retries: 1 #lift_speed: 10 #activate_gcode: # G4 P200 ;Wait 200ms # SET_TMC_CURRENT STEPPER=stepper_z CURRENT=0.4 # SET_TMC_CURRENT STEPPER=stepper_z1 CURRENT=0.4 # SET_TMC_CURRENT STEPPER=stepper_z2 CURRENT=0.4 # SET_TMC_CURRENT STEPPER=stepper_z3 CURRENT=0.4 #deactivate_gcode: # {% set run_current = printer.configfile.config['tmc2209 stepper_z'].run_current | float %} # SET_TMC_CURRENT STEPPER=stepper_z CURRENT={run_current} # SET_TMC_CURRENT STEPPER=stepper_z1 CURRENT={run_current} # SET_TMC_CURRENT STEPPER=stepper_z2 CURRENT={run_current} # SET_TMC_CURRENT STEPPER=stepper_z3 CURRENT={run_current} [input_shaper] shaper_freq_x: 91.4 shaper_freq_y: 70.0 shaper_type: 3hump_ei [force_move] enable_force_move: True #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [skew_correction calilantern_skew_profile] #*# xy_skew = 0.002269819397871509 #*# xz_skew = 0.0 #*# yz_skew = 0.0 #*# #*# [scanner] #*# mode = touch #*# scanner_touch_threshold = 3000 #*# scanner_touch_speed = 3 #*# scanner_touch_z_offset = 0.180 #*# #*# [scanner model default] #*# model_coef = 1.4576195916953936, #*# 1.785851337777226, #*# 0.7482684560674038, #*# 0.37149574454302975, #*# 0.45525587058229405, #*# 0.38020169514738367, #*# -0.3194453631539581, #*# -0.3210922662765739, #*# 0.3090302568640316, #*# 0.23578147304339162 #*# model_domain = 3.20112000993792e-07,3.3365602490491824e-07 #*# model_range = 0.200000,5.100000 #*# model_temp = 66.713254 #*# model_offset = 0.00000 #*# model_mode = touch #*# model_fw_version = CARTOGRAPHER 5.0.0 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# 0.003948, 0.007173, 0.007008, 0.003540, 0.010178, 0.008681, 0.005508, 0.003132, 0.005464, 0.013461, 0.019700, 0.021148, 0.023615, 0.022540, 0.020282, 0.016326, 0.014782, 0.017973, 0.024249, 0.032225, 0.043044, 0.050525, 0.050860, 0.048989, 0.043714, 0.037136, 0.027865, 0.019195, 0.015294, 0.021297 #*# 0.008409, 0.007676, 0.006805, 0.007626, 0.013361, 0.007530, 0.000759, 0.004054, 0.006251, 0.015086, 0.014817, 0.018099, 0.020481, 0.019536, 0.015810, 0.005453, 0.009504, 0.013436, 0.026799, 0.030026, 0.041719, 0.049339, 0.049378, 0.046674, 0.041463, 0.034524, 0.025703, 0.016546, 0.013367, 0.015277 #*# 0.010416, 0.010321, 0.014962, 0.010808, 0.006846, 0.010154, 0.009087, 0.011789, 0.008979, 0.008576, 0.015200, 0.019638, 0.018775, 0.017247, 0.015352, 0.011044, 0.009378, 0.011763, 0.020431, 0.029296, 0.042088, 0.050571, 0.049303, 0.046857, 0.041496, 0.035204, 0.027103, 0.018203, 0.013406, 0.019304 #*# 0.014058, 0.016559, 0.012998, 0.008717, 0.012748, 0.013081, 0.017272, 0.008193, 0.006888, 0.014109, 0.022775, 0.024345, 0.014946, 0.014753, 0.011715, 0.016942, 0.015192, 0.013303, 0.013278, 0.034517, 0.044996, 0.047786, 0.044660, 0.043084, 0.048412, 0.041002, 0.028604, 0.016533, 0.010949, 0.023071 #*# 0.013724, 0.008590, 0.013434, 0.017998, 0.014546, 0.015666, 0.012515, 0.014925, 0.016926, 0.018364, 0.020829, 0.018131, 0.022130, 0.019581, 0.017743, 0.013361, 0.012598, 0.014957, 0.020257, 0.030479, 0.040697, 0.047267, 0.049406, 0.047230, 0.044477, 0.038895, 0.030678, 0.019668, 0.015853, 0.021281 #*# 0.009555, 0.014874, 0.013745, 0.010583, 0.008174, 0.011485, 0.013847, 0.012879, 0.014855, 0.013233, 0.022738, 0.023520, 0.018476, 0.014850, 0.011724, 0.014966, 0.013386, 0.012464, 0.013162, 0.026705, 0.040161, 0.044194, 0.041515, 0.039956, 0.045283, 0.040331, 0.028842, 0.015920, 0.012994, 0.019705 #*# 0.009517, 0.009809, 0.012988, 0.008720, 0.009448, 0.008700, 0.010317, 0.012115, 0.011036, 0.016880, 0.019606, 0.022820, 0.016512, 0.016888, 0.015302, 0.011923, 0.008606, 0.011000, 0.017558, 0.024755, 0.036331, 0.042156, 0.042251, 0.041778, 0.037883, 0.036105, 0.028337, 0.020304, 0.017487, 0.021256 #*# 0.013834, 0.014160, 0.013409, 0.007094, 0.007139, 0.010916, 0.016466, 0.016970, 0.014110, 0.020433, 0.027358, 0.025910, 0.016540, 0.014902, 0.016851, 0.016465, 0.013685, 0.005429, 0.011663, 0.025262, 0.039108, 0.035227, 0.041247, 0.036445, 0.043934, 0.040348, 0.030358, 0.016634, 0.014857, 0.029726 #*# 0.005555, 0.010449, 0.014959, 0.011875, 0.002304, 0.006964, 0.010096, 0.015258, 0.018728, 0.014716, 0.019824, 0.019539, 0.020547, 0.013341, 0.010111, 0.008668, 0.008757, 0.008573, 0.012188, 0.021268, 0.033015, 0.040192, 0.040746, 0.036794, 0.038282, 0.036809, 0.031281, 0.018172, 0.015583, 0.022983 #*# 0.006987, 0.007345, 0.003849, 0.000726, 0.002670, 0.003738, 0.007001, 0.001530, 0.004586, 0.011653, 0.017136, 0.016852, 0.006988, 0.005487, 0.002483, 0.005726, 0.003786, 0.000644, 0.002324, 0.018241, 0.032160, 0.031591, 0.027678, 0.027494, 0.035223, 0.032077, 0.021459, 0.010301, 0.007098, 0.022800 #*# -0.004133, 0.003052, -0.003550, -0.003822, -0.007137, -0.003205, -0.003853, -0.003975, -0.001452, 0.001128, 0.008335, 0.006844, 0.005306, 0.003389, -0.000875, -0.002452, -0.006328, -0.005186, 0.002561, 0.011775, 0.018665, 0.023656, 0.024682, 0.022846, 0.021539, 0.019075, 0.013375, 0.006979, 0.004325, 0.009372 #*# -0.003480, -0.004016, -0.005023, -0.008059, -0.006465, -0.004002, -0.004088, -0.008771, -0.004922, 0.006335, 0.010217, 0.006089, 0.003463, -0.002469, 0.003523, -0.000673, -0.007582, -0.009019, 0.000207, 0.014187, 0.017558, 0.021937, 0.018046, 0.021740, 0.024397, 0.016344, 0.005884, 0.000644, 0.009149, 0.009387 #*# -0.005961, -0.008740, -0.010451, -0.010021, -0.008588, -0.008302, -0.008845, -0.007659, -0.002772, 0.004338, 0.007689, 0.007776, 0.004758, 0.007327, 0.001518, -0.004015, -0.006653, -0.007060, -0.001691, 0.007445, 0.015504, 0.019283, 0.022006, 0.019632, 0.018043, 0.016444, 0.012222, 0.005848, 0.003083, 0.007013 #*# -0.015213, -0.013566, -0.014790, -0.014577, -0.013620, -0.011631, -0.008557, -0.008188, -0.008946, -0.002394, 0.011414, 0.010310, 0.002136, -0.000569, -0.000478, -0.001484, -0.008014, -0.012079, -0.008127, 0.007150, 0.016437, 0.013330, 0.012562, 0.015116, 0.018517, 0.012577, 0.005540, -0.000902, 0.005549, 0.009607 #*# -0.015469, -0.018499, -0.011964, -0.008737, -0.009593, -0.011989, -0.010496, -0.003267, 0.001507, 0.005789, 0.008657, 0.011868, 0.008618, 0.003659, -0.001078, -0.004270, -0.005657, -0.004610, -0.000141, 0.003950, 0.014763, 0.018154, 0.019234, 0.016351, 0.016329, 0.015939, 0.014734, 0.007693, 0.002287, 0.005412 #*# -0.013019, -0.013686, -0.010997, -0.007558, -0.001629, -0.003629, -0.002416, 0.000678, 0.005208, 0.014837, 0.012561, 0.014508, 0.010390, 0.009901, 0.007762, -0.003920, -0.003062, -0.000979, 0.007516, 0.010190, 0.014165, 0.022700, 0.023621, 0.027324, 0.016664, 0.022047, 0.017489, 0.015008, 0.006729, 0.003654 #*# -0.011142, -0.005680, -0.008877, -0.008759, -0.001500, 0.001484, 0.003886, 0.004464, 0.007141, 0.012984, 0.018871, 0.017529, 0.012786, 0.009873, 0.007637, 0.004207, 0.002038, 0.001153, 0.005826, 0.014742, 0.023137, 0.027887, 0.028194, 0.027620, 0.025920, 0.025916, 0.021457, 0.014860, 0.012488, 0.015227 #*# -0.004516, -0.003671, -0.008733, -0.003564, 0.000620, 0.003920, 0.004693, 0.003927, 0.009624, 0.014719, 0.021945, 0.016547, 0.013387, 0.013180, 0.013287, 0.008272, 0.000759, 0.002885, 0.008044, 0.020363, 0.026568, 0.028169, 0.033924, 0.033711, 0.035229, 0.026797, 0.028264, 0.021418, 0.021233, 0.020412 #*# -0.003188, -0.003989, -0.002026, 0.000643, 0.001022, 0.000682, 0.002111, 0.005755, 0.009967, 0.013301, 0.018106, 0.020388, 0.018152, 0.013261, 0.009201, 0.005444, 0.003044, 0.003875, 0.010001, 0.019254, 0.028489, 0.034090, 0.036750, 0.035140, 0.032132, 0.032068, 0.028209, 0.022713, 0.019492, 0.021127 #*# 0.000633, 0.005736, 0.000875, 0.000779, 0.002329, 0.003118, 0.005013, 0.006174, 0.010528, 0.016532, 0.021537, 0.022872, 0.020126, 0.016731, 0.010488, 0.010944, 0.008758, 0.010922, 0.017140, 0.025434, 0.036131, 0.039876, 0.041349, 0.039120, 0.035144, 0.033082, 0.029828, 0.024327, 0.021510, 0.022327 #*# 0.010170, 0.005405, 0.005683, 0.005383, 0.005487, 0.004473, 0.005522, 0.006937, 0.010963, 0.016489, 0.021945, 0.022635, 0.020997, 0.017950, 0.015057, 0.013292, 0.012156, 0.013710, 0.021627, 0.029094, 0.038904, 0.042990, 0.044863, 0.042211, 0.037992, 0.035022, 0.032230, 0.028621, 0.024365, 0.025891 #*# 0.008779, 0.009115, 0.003965, 0.005044, 0.005496, 0.007141, 0.005848, 0.009434, 0.011733, 0.018682, 0.025876, 0.025178, 0.020542, 0.015144, 0.015670, 0.012780, 0.011668, 0.015246, 0.021877, 0.034545, 0.040661, 0.046264, 0.043072, 0.042725, 0.041772, 0.036798, 0.033781, 0.027461, 0.026705, 0.028168 #*# 0.010971, 0.002370, 0.003816, 0.005770, 0.004481, 0.003844, 0.003773, 0.006966, 0.009845, 0.016908, 0.022893, 0.023568, 0.019717, 0.015699, 0.013268, 0.009444, 0.008562, 0.011714, 0.021555, 0.030542, 0.039186, 0.042943, 0.043667, 0.040344, 0.036715, 0.036852, 0.036065, 0.032265, 0.028284, 0.027858 #*# 0.006969, 0.002616, -0.001881, 0.002548, 0.006617, 0.005535, 0.005266, 0.008688, 0.013208, 0.019579, 0.024395, 0.022752, 0.019223, 0.014763, 0.011740, 0.008145, 0.006646, 0.013502, 0.022219, 0.033877, 0.039747, 0.046021, 0.044249, 0.041941, 0.042301, 0.040710, 0.039963, 0.035011, 0.029913, 0.030067 #*# 0.010986, 0.005226, 0.004302, 0.007276, 0.008429, 0.009177, 0.009812, 0.011832, 0.016602, 0.020374, 0.024286, 0.024254, 0.019366, 0.013777, 0.011746, 0.011094, 0.011791, 0.017386, 0.027512, 0.036856, 0.044776, 0.049212, 0.048838, 0.046417, 0.046353, 0.048820, 0.047160, 0.040684, 0.035155, 0.034684 #*# 0.008554, 0.003149, 0.000668, 0.004845, 0.007136, 0.005868, 0.006945, 0.010215, 0.014983, 0.019183, 0.021194, 0.019678, 0.018931, 0.015136, 0.010274, 0.007087, 0.008169, 0.016765, 0.025172, 0.035683, 0.040663, 0.049210, 0.049283, 0.046466, 0.044263, 0.044675, 0.046209, 0.038471, 0.032515, 0.030404 #*# 0.009343, 0.004128, 0.002199, 0.004633, 0.004020, 0.002398, 0.002900, 0.005321, 0.009138, 0.013336, 0.016537, 0.016535, 0.014341, 0.010967, 0.007773, 0.005296, 0.007026, 0.011774, 0.018325, 0.029082, 0.036958, 0.039956, 0.042152, 0.042655, 0.041525, 0.041150, 0.036963, 0.030997, 0.026926, 0.027586 #*# 0.011390, 0.003933, 0.002111, 0.000445, -0.000235, -0.001288, -0.002173, 0.000757, 0.004667, 0.009873, 0.012735, 0.014145, 0.011507, 0.007600, 0.004148, 0.000927, 0.004728, 0.008675, 0.015374, 0.023342, 0.028746, 0.035178, 0.038351, 0.040053, 0.038745, 0.035225, 0.030547, 0.028565, 0.024329, 0.020875 #*# 0.009158, 0.004975, 0.002680, 0.000821, 0.001779, 0.000932, 0.000702, 0.003518, 0.005352, 0.010614, 0.015212, 0.015010, 0.012521, 0.009649, 0.006089, 0.004132, 0.005464, 0.007263, 0.013337, 0.022282, 0.029789, 0.035306, 0.037706, 0.038410, 0.038425, 0.038374, 0.034368, 0.027860, 0.023667, 0.024268 #*# 0.011938, 0.007894, 0.003792, 0.000737, 0.000817, 0.002125, 0.001961, 0.003755, 0.006560, 0.010024, 0.014161, 0.015000, 0.011705, 0.008642, 0.006231, 0.005409, 0.005714, 0.008605, 0.013028, 0.020729, 0.028954, 0.035990, 0.038754, 0.039360, 0.037544, 0.038639, 0.033369, 0.026722, 0.022891, 0.025716 #*# x_count = 30 #*# y_count = 30 #*# mesh_x_pps = 2 #*# mesh_y_pps = 2 #*# algo = bicubic #*# tension = 0.2 #*# min_x = 30.0 #*# max_x = 310.0 #*# min_y = 30.0 #*# max_y = 310.0