PZ+Eddy, apart from print_start messes up
This commit is contained in:
parent
481350784d
commit
3c127c74b3
2 changed files with 127 additions and 107 deletions
|
|
@ -16,6 +16,8 @@ gcode:
|
|||
M140 S0 ; turn off power to the bed, interference with probe?
|
||||
SET_GCODE_OFFSET Z=0.0 ; Reset the G-Code Z offset so we can set it manually later. we don't care if move=1|0 because we're about to home anyway.
|
||||
G28 Z ; Heatsoaked, validate that z
|
||||
G90 ; ensure absolute positioning (how would it be something else?!
|
||||
G1 Z10 F3000
|
||||
QUAD_GANTRY_LEVEL
|
||||
STATUS_MESHING
|
||||
BED_MESH_CALIBRATE
|
||||
|
|
@ -25,7 +27,7 @@ gcode:
|
|||
CLEAN_NOZZLE
|
||||
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
|
||||
G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position
|
||||
SET_GCODE_OFFSET Z_ADJUST=-0.45 MOVE=1 ; This is how we will permanently save the Z offset without having to care about type of probe.
|
||||
#SET_GCODE_OFFSET Z_ADJUST=-0.45 MOVE=1 ; This is how we will permanently save the Z offset without having to care about type of probe.
|
||||
G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line
|
||||
G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little
|
||||
G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line
|
||||
|
|
@ -330,68 +332,80 @@ gcode:
|
|||
G1 E-{unload_distance} F{max_velocity} # fast-unload
|
||||
RESTORE_GCODE_STATE NAME=unload_state
|
||||
|
||||
# [gcode_macro _SAFE_X_HOME]
|
||||
# ; This macro is to ensure that we're not at y=home when X is homed.
|
||||
# gcode:
|
||||
# {% if 'Y' in printer.toolhead.homed_axes %}
|
||||
# G91
|
||||
# G0 Y-20 F50000
|
||||
# G90
|
||||
# {% else %}
|
||||
# G90
|
||||
# SET_KINEMATIC_POSITION Y=20
|
||||
# G0 Y0 F50000
|
||||
# G28 X
|
||||
# {% endif %}
|
||||
[gcode_macro _SAFE_X_HOME]
|
||||
; This macro is to ensure that we're not at y=home when X is homed.
|
||||
gcode:
|
||||
{% if 'Y' in printer.toolhead.homed_axes %}
|
||||
G91
|
||||
G0 Y-20 F50000
|
||||
G90
|
||||
{% else %}
|
||||
G90
|
||||
SET_KINEMATIC_POSITION Y=20
|
||||
G0 Y0 F50000
|
||||
G28 X
|
||||
{% endif %}
|
||||
|
||||
# [gcode_macro _SAFE_Z_HOME_LIFT]
|
||||
# ; Lift the Z no matter what (replicate z-hop from [safe_z_home]
|
||||
# gcode:
|
||||
# {% if 'Z' in printer.toolhead.homed_axes %}
|
||||
# G91
|
||||
# G0 Z10 F1000
|
||||
# G90
|
||||
# {% else %}
|
||||
# G90
|
||||
# SET_KINEMATIC_POSITION Z=0
|
||||
# G0 Z10 F1000
|
||||
# {% endif %}
|
||||
[gcode_macro _SAFE_Z_HOME_LIFT]
|
||||
; Lift the Z no matter what (replicate z-hop from [safe_z_home]
|
||||
gcode:
|
||||
{% if 'Z' in printer.toolhead.homed_axes %}
|
||||
G91
|
||||
G0 Z10 F1000
|
||||
G90
|
||||
{% else %}
|
||||
G90
|
||||
SET_KINEMATIC_POSITION Z=0
|
||||
G0 Z10 F1000
|
||||
{% endif %}
|
||||
|
||||
# [gcode_macro _SAFE_Z_HOME]
|
||||
# ; this macro recreates the save_z_home setup center the toolhead before z home.
|
||||
# gcode:
|
||||
# {% if not 'X' in printer.toolhead.homed_axes %}
|
||||
# _SAFE_X_HOME
|
||||
# {% endif %}
|
||||
# {% if not 'Y' in printer.toolhead.homed_axes %}
|
||||
# G28 Y
|
||||
# {% endif %}
|
||||
# G0 X175 Y175 F50000
|
||||
# G28 Z
|
||||
[gcode_macro _SAFE_Z_HOME]
|
||||
; this macro recreates the save_z_home setup center the toolhead before z home.
|
||||
gcode:
|
||||
{% if not 'X' in printer.toolhead.homed_axes %}
|
||||
_SAFE_X_HOME
|
||||
{% endif %}
|
||||
{% if not 'Y' in printer.toolhead.homed_axes %}
|
||||
G28 Y
|
||||
{% endif %}
|
||||
G0 X175 Y175 F50000
|
||||
G4 P200 ;Wait 200ms
|
||||
SET_TMC_CURRENT STEPPER=stepper_z CURRENT=0.4
|
||||
SET_TMC_CURRENT STEPPER=stepper_z1 CURRENT=0.4
|
||||
SET_TMC_CURRENT STEPPER=stepper_z2 CURRENT=0.4
|
||||
SET_TMC_CURRENT STEPPER=stepper_z3 CURRENT=0.4
|
||||
G28 Z
|
||||
{% set run_current = printer.configfile.config['tmc2209 stepper_z'].run_current | float %}
|
||||
SET_TMC_CURRENT STEPPER=stepper_z CURRENT={run_current}
|
||||
SET_TMC_CURRENT STEPPER=stepper_z1 CURRENT={run_current}
|
||||
SET_TMC_CURRENT STEPPER=stepper_z2 CURRENT={run_current}
|
||||
SET_TMC_CURRENT STEPPER=stepper_z3 CURRENT={run_current}
|
||||
SET_KINEMATIC_POSITION Z=0
|
||||
G0 Z10 F3000
|
||||
|
||||
# [homing_override]
|
||||
# ; The ebb36 mount often catches on the drag chain at the back of the printer.
|
||||
# ; This ensures that if X is asked to be homed, first Y is homed and then y is
|
||||
# ; moved away from the back of the printer and then homed.
|
||||
# axes: xyz
|
||||
# gcode:
|
||||
# #z hop no matter what
|
||||
# _SAFE_Z_HOME_LIFT
|
||||
# {% if not 'Z' in params and not 'Y' in params and 'X' in params %} # Home X
|
||||
# _SAFE_X_HOME
|
||||
# {% elif not 'Z' in params and not 'X' in params and 'Y' in params %} #Home Y
|
||||
# G28 Y
|
||||
# {% elif not 'Z' in params and 'X' in params and 'Y' in params %} #Home X+Y
|
||||
# _SAFE_X_HOME
|
||||
# G28 Y
|
||||
# {% elif 'Z' in params and not 'X' in params and not 'Y' in params %} # Home Z
|
||||
# _SAFE_Z_HOME
|
||||
# {% else %} #Home X+Y+Z
|
||||
# _SAFE_X_HOME
|
||||
# G28 Y
|
||||
# _SAFE_Z_HOME
|
||||
# {% endif %}
|
||||
[homing_override]
|
||||
; The ebb36 mount often catches on the drag chain at the back of the printer.
|
||||
; This ensures that if X is asked to be homed, first Y is homed and then y is
|
||||
; moved away from the back of the printer and then homed.
|
||||
axes: xyz
|
||||
gcode:
|
||||
#z hop no matter what
|
||||
_SAFE_Z_HOME_LIFT
|
||||
{% if not 'Z' in params and not 'Y' in params and 'X' in params %} # Home X
|
||||
_SAFE_X_HOME
|
||||
{% elif not 'Z' in params and not 'X' in params and 'Y' in params %} #Home Y
|
||||
G28 Y
|
||||
{% elif not 'Z' in params and 'X' in params and 'Y' in params %} #Home X+Y
|
||||
_SAFE_X_HOME
|
||||
G28 Y
|
||||
{% elif 'Z' in params and not 'X' in params and not 'Y' in params %} # Home Z
|
||||
_SAFE_Z_HOME
|
||||
{% else %} #Home X+Y+Z
|
||||
_SAFE_X_HOME
|
||||
G28 Y
|
||||
_SAFE_Z_HOME
|
||||
{% endif %}
|
||||
|
||||
|
||||
[mmu_led_effect mmu_purple_slow]
|
||||
layers: breathing 1.0 0 top (1,0,1)
|
||||
layers: breathing 1.0 0 top (1,0,1)
|
||||
|
|
|
|||
100
printer.cfg
100
printer.cfg
|
|
@ -36,7 +36,7 @@ canbus_uuid: 970febd72165
|
|||
[include fluidd.cfg]
|
||||
[include stealthburner_leds.cfg]
|
||||
[include bedfans.cfg]
|
||||
[include eddy_macros.cfg]
|
||||
#[include eddy_macros.cfg]
|
||||
[include martyn_macros.cfg]
|
||||
[include shaketune.cfg]
|
||||
|
||||
|
|
@ -118,16 +118,16 @@ enable_pin: !PG5
|
|||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 32
|
||||
#endstop_pin: PG10
|
||||
endstop_pin:probe:z_virtual_endstop
|
||||
#endstop_pin: probe:z_virtual_endstop
|
||||
endstop_pin: !ebb36:PB7
|
||||
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||
## (+) value = endstop above Z0, (-) value = endstop below
|
||||
## Increasing position_endstop brings nozzle closer to the bed
|
||||
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
||||
#position_endstop: -0.5
|
||||
position_endstop: 0
|
||||
position_max: 310
|
||||
position_min: -10
|
||||
homing_speed: 15
|
||||
homing_speed: 5
|
||||
second_homing_speed: 3
|
||||
homing_retract_dist: 3
|
||||
|
||||
|
|
@ -288,16 +288,16 @@ gcode_id: chamber_th
|
|||
timeout: 1800
|
||||
|
||||
# Need to work out how eddy interferes with magic home
|
||||
[safe_z_home]
|
||||
#[safe_z_home]
|
||||
## XY Location of the Z Endstop Switch
|
||||
## Update -10,-10 to the XY coordinates of your endstop pin
|
||||
## (such as 157,305) after going through Z Endstop Pin
|
||||
## Location Definition step.
|
||||
#home_xy_position:232,350
|
||||
home_xy_position: 175,175
|
||||
speed:100
|
||||
z_hop:10
|
||||
z_hop_speed:10
|
||||
#home_xy_position: 175,175
|
||||
#speed:100
|
||||
#z_hop:10
|
||||
#z_hop_speed:10
|
||||
|
||||
|
||||
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||
|
|
@ -391,25 +391,32 @@ sensor_type: temperature_mcu
|
|||
# Macros
|
||||
#####################################################################
|
||||
|
||||
|
||||
# pre-cartographer
|
||||
# [probe]
|
||||
# pin: ebb36:PB9
|
||||
# x_offset: 0
|
||||
# y_offset: 19.75
|
||||
# #z_offset: 5.930
|
||||
# # below is default, trying -0.365 measured, if +0.365, it's 6.785
|
||||
# # z_offset: 6.42
|
||||
# speed: 5
|
||||
# samples: 3
|
||||
# samples_result: median
|
||||
# sample_retract_dist: 2.0
|
||||
# samples_tolerance: 0.01
|
||||
# samples_tolerance_retries: 4
|
||||
#[probe] ## Other parameters in config.cfg
|
||||
#pin: !ebb36:PB7
|
||||
#x_offset: 0.0
|
||||
#y_offset: 0.0
|
||||
#z_offset: 0.0
|
||||
#speed: 5.0 # Speed (in mm/s) of the Z axis when probing. The default is 5mm/s.
|
||||
#samples: 2
|
||||
#sample_retract_dist: 3.0
|
||||
#samples_tolerance_retries: 1
|
||||
#lift_speed: 10
|
||||
#activate_gcode:
|
||||
# G4 P200 ;Wait 200ms
|
||||
# SET_TMC_CURRENT STEPPER=stepper_z CURRENT=0.4
|
||||
# SET_TMC_CURRENT STEPPER=stepper_z1 CURRENT=0.4
|
||||
# SET_TMC_CURRENT STEPPER=stepper_z2 CURRENT=0.4
|
||||
# SET_TMC_CURRENT STEPPER=stepper_z3 CURRENT=0.4
|
||||
#deactivate_gcode:
|
||||
# {% set run_current = printer.configfile.config['tmc2209 stepper_z'].run_current | float %}
|
||||
# SET_TMC_CURRENT STEPPER=stepper_z CURRENT={run_current}
|
||||
# SET_TMC_CURRENT STEPPER=stepper_z1 CURRENT={run_current}
|
||||
# SET_TMC_CURRENT STEPPER=stepper_z2 CURRENT={run_current}
|
||||
# SET_TMC_CURRENT STEPPER=stepper_z3 CURRENT={run_current}
|
||||
|
||||
[bed_mesh]
|
||||
speed: 200
|
||||
horizontal_move_z: 2
|
||||
horizontal_move_z: 3
|
||||
mesh_min: 35, 35
|
||||
mesh_max: 310, 310
|
||||
zero_reference_position: 175, 175
|
||||
|
|
@ -439,36 +446,35 @@ sensor_type: Generic 3950
|
|||
sensor_pin: eddy:gpio26
|
||||
horizontal_move_z: 2
|
||||
|
||||
[gcode_macro PROBE_EDDY_CURRENT_CALIBRATE_AUTO]
|
||||
gcode:
|
||||
BED_MESH_CLEAR
|
||||
G28 X Y
|
||||
G90 # Abs positioning
|
||||
G1 X{ printer.toolhead.axis_maximum.x/2 } Y{ printer.toolhead.axis_maximum.y/2 } F6000
|
||||
{% if 'z' not in printer.toolhead.homed_axes %}
|
||||
SET_KINEMATIC_POSITION Z={ printer.toolhead.axis_maximum.z-1 } # Allows the user to work it down until it touches.
|
||||
{% endif %}
|
||||
PROBE_EDDY_CURRENT_CALIBRATE {rawparams}
|
||||
|
||||
[force_move]
|
||||
enable_force_move: True
|
||||
|
||||
# Let's not yet...
|
||||
#[filament_motion_sensor encoder_sensor]
|
||||
#switch_pin: PG12
|
||||
#detection_length: 2.88
|
||||
#extruder: extruder
|
||||
#pause_on_runout: False
|
||||
#runout_gcode:
|
||||
# PAUSE # [pause_resume] is required in printer.cfg
|
||||
# M117 Filament encoder runout
|
||||
#insert_gcode:
|
||||
# M117 Filament encoder inserted
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# -0.009752, -0.002567, -0.002418, 0.024205, 0.023133, 0.034214, 0.043152, 0.023689, 0.019876
|
||||
#*# -0.010467, 0.005144, 0.009298, 0.020234, 0.017335, 0.019320, 0.050222, 0.023133, 0.012251
|
||||
#*# -0.015067, -0.008072, 0.008400, 0.001699, 0.002224, 0.006005, 0.032586, 0.017454, 0.006868
|
||||
#*# -0.032029, -0.022778, -0.015593, -0.005487, 0.000614, 0.001551, 0.017335, -0.000508, -0.004438
|
||||
#*# -0.049611, -0.034939, -0.013534, -0.020047, -0.000172, -0.003281, 0.009074, -0.003953, -0.016267
|
||||
#*# -0.037046, -0.016647, -0.014397, -0.011667, 0.001699, 0.004956, 0.013322, -0.001182, -0.004289
|
||||
#*# -0.023830, -0.015781, 0.013680, -0.001369, 0.004619, 0.011852, 0.026403, 0.009747, -0.001706
|
||||
#*# -0.027613, -0.002580, 0.005144, 0.008737, 0.005144, 0.027502, 0.034771, 0.019320, 0.017335
|
||||
#*# -0.020910, -0.010278, 0.004807, 0.005144, 0.003946, 0.018764, 0.027145, 0.012608, 0.006342
|
||||
#*# -0.013814, 0.002245, 0.005321, 0.037976, 0.048046, 0.060540, 0.070946, 0.056286, 0.060975
|
||||
#*# -0.001514, -0.003904, 0.018992, 0.015656, 0.024350, 0.037976, 0.057306, 0.054291, 0.038143
|
||||
#*# -0.032466, -0.007290, 0.009769, 0.005321, 0.029468, 0.034263, 0.062378, 0.049342, 0.044221
|
||||
#*# -0.041181, -0.025479, -0.007925, -0.000403, 0.004208, 0.031030, 0.042659, 0.031605, 0.029899
|
||||
#*# -0.059714, -0.035092, -0.003052, -0.006128, -0.000229, 0.008656, 0.032592, 0.019419, 0.030166
|
||||
#*# -0.062837, -0.016463, -0.010738, 0.004044, -0.000826, 0.024083, 0.047180, 0.033722, 0.040834
|
||||
#*# -0.040349, -0.016038, 0.003360, 0.008820, 0.014120, 0.031030, 0.053163, 0.038785, 0.043882
|
||||
#*# -0.027854, -0.012273, 0.009507, 0.015658, 0.020269, 0.042397, 0.052996, 0.039967, 0.049342
|
||||
#*# -0.021443, -0.001939, 0.002669, 0.013694, 0.017621, 0.031032, 0.048044, 0.044225, 0.041100
|
||||
#*# x_count = 9
|
||||
#*# y_count = 9
|
||||
#*# mesh_x_pps = 9
|
||||
|
|
|
|||
Loading…
Add table
Reference in a new issue