Automatic commit of config from 2025-06-21
This commit is contained in:
parent
f81c1a7da4
commit
33a05f7bd7
3 changed files with 75 additions and 13 deletions
|
|
@ -16,36 +16,52 @@ gcode:
|
|||
STATUS_HOMING
|
||||
G92 E0 ; Reset Extruder
|
||||
BED_MESH_CLEAR
|
||||
RESPOND PREFIX=DEBUG: MSG="G28"
|
||||
G28 ; Home all axes
|
||||
;QUAD_GANTRY_LEVEL
|
||||
STATUS_HEATING
|
||||
;TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={STANDBY_TEMP} ; Start heating up the nozzle most of the way
|
||||
{% if "ABS" == MATERIAL_TYPE %}
|
||||
RESPOND PREFIX=DEBUG: MSG="ABS, Preheating bed for heat-soak"
|
||||
M117 Bed to 100{"\xf8"}C...
|
||||
M190 S100
|
||||
{% endif %}
|
||||
M117 Chamber to {CHAMBER_TEMP}{"\xf8"}C...
|
||||
M117 Chamber to {CHAMBER_TEMP}C...
|
||||
RESPOND PREFIX=DEBUG: MSG="Wait for chamber to {CHAMBER_TEMP}C"
|
||||
TEMPERATURE_WAIT SENSOR="temperature_sensor chamber_temp" MINIMUM={CHAMBER_TEMP} ; Wait for chamber temp
|
||||
M117 Bed to {BED_TEMP}C...
|
||||
RESPOND PREFIX=DEBUG: MSG="Set Bed to {BED_TEMP}C"
|
||||
M140 S{BED_TEMP} ; Set the bed temp to the original request (might be lower than preheat)
|
||||
M117 Gantry Level
|
||||
RESPOND PREFIX=DEBUG: MSG="QGL"
|
||||
QUAD_GANTRY_LEVEL
|
||||
M117 Bed mesh eddy scan
|
||||
STATUS_MESHING
|
||||
RESPOND PREFIX=DEBUG: MSG="Homing Z"
|
||||
G28 Z
|
||||
RESPOND PREFIX=DEBUG: MSG="Mesh scan"
|
||||
BED_MESH_CALIBRATE ;Well, this is fine and dandy...
|
||||
M117 Cleaning nozzle
|
||||
RESPOND PREFIX=DEBUG: MSG="Preheating nozzle to clean (non-ooze) temp S{CLEAN_TEMP}C"
|
||||
M109 S{CLEAN_TEMP}
|
||||
RESPOND PREFIX=DEBUG: MSG="CLEAN_NOZZLE macro"
|
||||
CLEAN_NOZZLE
|
||||
M117 Carto Touch
|
||||
RESPOND PREFIX=DEBUG: MSG="Homing Z"
|
||||
G28 Z
|
||||
RESPOND PREFIX=DEBUG: MSG="CARTOGRAPHER_TOUCH macro"
|
||||
CARTOGRAPHER_TOUCH
|
||||
RESPOND PREFIX=DEBUG: MSG="Lifting Z a little more"
|
||||
G1 Z10 ; carto leaves it at Z=5 which is theoretically okay, but cleaning then might skip steps and cause problems.
|
||||
M117 Final heat {EXTRUDER_TEMP}/{BED_TEMP}
|
||||
RESPOND PREFIX=DEBUG: MSG="Final heat {EXTRUDER_TEMP}/{BED_TEMP}"
|
||||
STATUS_HEATING
|
||||
M190 S{BED_TEMP} ; Start heating the bed, wait until target temperature reached
|
||||
M109 S{EXTRUDER_TEMP} ; Finish heating the nozzle
|
||||
M117 Clean and prime
|
||||
RESPOND PREFIX=DEBUG: MSG="CLEAN_NOZZLE macro (wipe ooze before prime line)"
|
||||
CLEAN_NOZZLE
|
||||
RESPOND PREFIX=DEBUG: MSG="PRIME LINE"
|
||||
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
|
||||
G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position
|
||||
G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line
|
||||
|
|
@ -54,9 +70,11 @@ gcode:
|
|||
G92 E0 ; Reset Extruder
|
||||
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
|
||||
G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish
|
||||
RESPOND PREFIX=DEBUG: MSG="SKEW_PROFILE LOAD=calilantern_skew_profile"
|
||||
SKEW_PROFILE LOAD=calilantern_skew_profile
|
||||
M117 Print started
|
||||
STATUS_PRINTING
|
||||
RESPOND PREFIX=DEBUG: MSG="Handing to slicer GCODE"
|
||||
|
||||
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
||||
[gcode_macro PRINT_END]
|
||||
|
|
|
|||
|
|
@ -1,5 +1,5 @@
|
|||
[Variables]
|
||||
mmu__revision = 3894
|
||||
mmu__revision = 3938
|
||||
mmu_calibration_bowden_home = 'encoder'
|
||||
mmu_calibration_bowden_lengths = [1425.1, 1425.1, 1425.1, 1425.1, 1425.1, 1425.1, 1425.1, 1425.1]
|
||||
mmu_calibration_clog_length = 8.9
|
||||
|
|
@ -24,7 +24,7 @@ mmu_state_gate_temperature = [200, 200, 200, 200, 200, 200, 200, 200]
|
|||
mmu_state_last_tool = -1
|
||||
mmu_state_tool_selected = 0
|
||||
mmu_state_tool_to_gate_map = [2, 2, 2, 2, 2, 2, 2, 2]
|
||||
mmu_statistics_counters = {'servo_down': {'count': 1152, 'limit': 5000, 'warning': 'Inspect servo arm for wear/damage', 'pause': False}, 'mmu_restarts': {'count': 270, 'limit': -1, 'warning': ''}, 'cutter_blade': {'count': 67, 'limit': 3000, 'warning': 'Inspect/replace filament cutting blade', 'pause': False}}
|
||||
mmu_statistics_counters = {'servo_down': {'count': 1154, 'limit': 5000, 'warning': 'Inspect servo arm for wear/damage', 'pause': False}, 'mmu_restarts': {'count': 277, 'limit': -1, 'warning': ''}, 'cutter_blade': {'count': 67, 'limit': 3000, 'warning': 'Inspect/replace filament cutting blade', 'pause': False}}
|
||||
mmu_statistics_gate_0 = {'pauses': 0, 'loads': 2, 'load_distance': 0.0, 'load_delta': 0.0, 'unloads': 0, 'unload_distance': 0.0, 'unload_delta': 0.0, 'load_failures': 2, 'unload_failures': 0, 'quality': -1.0}
|
||||
mmu_statistics_gate_1 = {'pauses': 7, 'loads': 17, 'load_distance': 21959.049, 'load_delta': 7303.358, 'unloads': 16, 'unload_distance': 9610.7, 'unload_delta': 534.671, 'load_failures': 8, 'unload_failures': 5, 'quality': 0.39797587469336376}
|
||||
mmu_statistics_gate_2 = {'pauses': 1, 'loads': 17, 'load_distance': 20817.321, 'load_delta': 4752.43, 'unloads': 18, 'unload_distance': 15111.1, 'unload_delta': 1780.351, 'load_failures': 8, 'unload_failures': 3, 'quality': 0.5951171707295873}
|
||||
|
|
|
|||
64
printer.cfg
64
printer.cfg
|
|
@ -443,22 +443,66 @@ enable_force_move: True
|
|||
#*# mode = touch
|
||||
#*# scanner_touch_threshold = 3000
|
||||
#*# scanner_touch_speed = 3
|
||||
#*# scanner_touch_z_offset = 0.200
|
||||
#*# scanner_touch_z_offset = 0.230
|
||||
#*#
|
||||
#*# [scanner model default]
|
||||
#*# model_coef = 1.4576195916953936,
|
||||
#*# 1.785851337777226,
|
||||
#*# 0.7482684560674038,
|
||||
#*# 0.37149574454302975,
|
||||
#*# 0.45525587058229405,
|
||||
#*# 0.38020169514738367,
|
||||
#*# -0.3194453631539581,
|
||||
#*# -0.3210922662765739,
|
||||
#*# 0.3090302568640316,
|
||||
#*# 0.23578147304339162
|
||||
#*# 1.785851337777226,
|
||||
#*# 0.7482684560674038,
|
||||
#*# 0.37149574454302975,
|
||||
#*# 0.45525587058229405,
|
||||
#*# 0.38020169514738367,
|
||||
#*# -0.3194453631539581,
|
||||
#*# -0.3210922662765739,
|
||||
#*# 0.3090302568640316,
|
||||
#*# 0.23578147304339162
|
||||
#*# model_domain = 3.20112000993792e-07,3.3365602490491824e-07
|
||||
#*# model_range = 0.200000,5.100000
|
||||
#*# model_temp = 66.713254
|
||||
#*# model_offset = 0.00000
|
||||
#*# model_mode = touch
|
||||
#*# model_fw_version = CARTOGRAPHER 5.0.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.005428, 0.012634, 0.007922, 0.008674, 0.006418, 0.010329, 0.007932, 0.006014, 0.009595, 0.015761, 0.020520, 0.023058, 0.026490, 0.027599, 0.020490, 0.015797, 0.016936, 0.020125, 0.031369, 0.032576, 0.042203, 0.053004, 0.059258, 0.054650, 0.042276, 0.038406, 0.029820, 0.025497, 0.012680, 0.017365
|
||||
#*# 0.004790, 0.011021, 0.010218, 0.007725, 0.007282, 0.004784, 0.008024, 0.008021, 0.004726, 0.007790, 0.016417, 0.021598, 0.020549, 0.018569, 0.015993, 0.014275, 0.012965, 0.014550, 0.020528, 0.032385, 0.045232, 0.051797, 0.052251, 0.049158, 0.043429, 0.035957, 0.026688, 0.018257, 0.014988, 0.021464
|
||||
#*# 0.003771, 0.008491, 0.012805, 0.012808, 0.007205, 0.006526, 0.008244, 0.009532, 0.007924, 0.011031, 0.015089, 0.018811, 0.018938, 0.018860, 0.015798, 0.011106, 0.008000, 0.010373, 0.022175, 0.033695, 0.040683, 0.046047, 0.049921, 0.051437, 0.043168, 0.032733, 0.022794, 0.023016, 0.018895, 0.019352
|
||||
#*# 0.007861, 0.010479, 0.014312, 0.014399, 0.007926, 0.011496, 0.015699, 0.015829, 0.007870, 0.011102, 0.018316, 0.022281, 0.021319, 0.015760, 0.014365, 0.012794, 0.013316, 0.010978, 0.018935, 0.032091, 0.044241, 0.050013, 0.049998, 0.048376, 0.045692, 0.037845, 0.029770, 0.020603, 0.016772, 0.020957
|
||||
#*# 0.008853, 0.014237, 0.009918, 0.006017, 0.010968, 0.015798, 0.014616, 0.009469, 0.009794, 0.015789, 0.018877, 0.019014, 0.018813, 0.018710, 0.015894, 0.013305, 0.012495, 0.014311, 0.020720, 0.029835, 0.040400, 0.049105, 0.051427, 0.048351, 0.042437, 0.037854, 0.032869, 0.021803, 0.014595, 0.018761
|
||||
#*# 0.006143, 0.010447, 0.007105, 0.001626, 0.007148, 0.011111, 0.012413, 0.009530, 0.011325, 0.011719, 0.020607, 0.020901, 0.016660, 0.013654, 0.016005, 0.014002, 0.010237, 0.012093, 0.015780, 0.027652, 0.039329, 0.045320, 0.045962, 0.043745, 0.043669, 0.038243, 0.031504, 0.023313, 0.017625, 0.023202
|
||||
#*# -0.003000, 0.008120, 0.009439, 0.003366, 0.000193, 0.002943, 0.009467, 0.011813, 0.010758, 0.012688, 0.016529, 0.019691, 0.016194, 0.014726, 0.012784, 0.010329, 0.008117, 0.009878, 0.017372, 0.026702, 0.035479, 0.042605, 0.044561, 0.043702, 0.039071, 0.036742, 0.030527, 0.023537, 0.020410, 0.023498
|
||||
#*# 0.001967, 0.004107, 0.006818, 0.003170, 0.003171, 0.000030, 0.009633, 0.011914, 0.011877, 0.012784, 0.018536, 0.020931, 0.016530, 0.015201, 0.011489, 0.014002, 0.011007, 0.009144, 0.013391, 0.021804, 0.036855, 0.039771, 0.042751, 0.038318, 0.040573, 0.039103, 0.030707, 0.023204, 0.018905, 0.027623
|
||||
#*# -0.003120, 0.007881, 0.006377, -0.000455, -0.003195, 0.000823, 0.006297, 0.009545, 0.009157, 0.011007, 0.015607, 0.016149, 0.012814, 0.011109, 0.008011, 0.006206, 0.004071, 0.004263, 0.011275, 0.021960, 0.031697, 0.037804, 0.040707, 0.040299, 0.038756, 0.035727, 0.030712, 0.023712, 0.020416, 0.025102
|
||||
#*# 0.000469, 0.000044, -0.005826, -0.007897, -0.008962, -0.000759, -0.003849, -0.006291, -0.002367, 0.008731, 0.011948, 0.008398, 0.003192, 0.001496, 0.006599, 0.001798, -0.003886, -0.004821, 0.005714, 0.019156, 0.025805, 0.028401, 0.029450, 0.034807, 0.033776, 0.028161, 0.019356, 0.014321, 0.015866, 0.018797
|
||||
#*# -0.016665, -0.012665, -0.009393, -0.013438, -0.016576, -0.014163, -0.012414, -0.011679, -0.007624, -0.004610, -0.001388, -0.000563, -0.000731, -0.002240, -0.005106, -0.007888, -0.010907, -0.009217, -0.000686, 0.009547, 0.017336, 0.022022, 0.022957, 0.022375, 0.020531, 0.019611, 0.015075, 0.008686, 0.006309, 0.012350
|
||||
#*# -0.015757, -0.013668, -0.013289, -0.018949, -0.016489, -0.014779, -0.014939, -0.014246, -0.010006, -0.006043, 0.000087, 0.000386, -0.001782, -0.004385, -0.005492, -0.008431, -0.011233, -0.009924, -0.005334, 0.005826, 0.014222, 0.023794, 0.018939, 0.021133, 0.019602, 0.021583, 0.012969, 0.004435, 0.005628, 0.011003
|
||||
#*# -0.017732, -0.025235, -0.022272, -0.020563, -0.017256, -0.020466, -0.020667, -0.015821, -0.009436, -0.004668, -0.001909, 0.000648, -0.001821, -0.001526, -0.004318, -0.009414, -0.012097, -0.011057, -0.006097, 0.002827, 0.012283, 0.017411, 0.018808, 0.018831, 0.016680, 0.015066, 0.011302, 0.007663, 0.004775, 0.009534
|
||||
#*# -0.027013, -0.023571, -0.023938, -0.024449, -0.024566, -0.017436, -0.017278, -0.017385, -0.016318, -0.005683, 0.004825, 0.000439, -0.003844, -0.001231, -0.005090, -0.006796, -0.014435, -0.014622, -0.006996, 0.004929, 0.012734, 0.013983, 0.015850, 0.015264, 0.017414, 0.010864, 0.007963, 0.006192, 0.006473, 0.008770
|
||||
#*# -0.026288, -0.032524, -0.031270, -0.019514, -0.016562, -0.019581, -0.019150, -0.015477, -0.008155, -0.001391, 0.001605, 0.001759, 0.000337, -0.002733, -0.005999, -0.009525, -0.011695, -0.009450, -0.004039, 0.001334, 0.009739, 0.015847, 0.017660, 0.016537, 0.015859, 0.015577, 0.013450, 0.008482, 0.005530, 0.006860
|
||||
#*# -0.025190, -0.025150, -0.021412, -0.022376, -0.018943, -0.014581, -0.007998, -0.008396, -0.006266, -0.000061, 0.011419, 0.011563, -0.000063, -0.003127, -0.001499, 0.000000, -0.004215, -0.009304, -0.006216, 0.007179, 0.020500, 0.016381, 0.015788, 0.020408, 0.022335, 0.025295, 0.017481, 0.007197, 0.007211, 0.010258
|
||||
#*# -0.024021, -0.018994, -0.021153, -0.016504, -0.011125, -0.011062, -0.007707, -0.004756, -0.001660, 0.004819, 0.011014, 0.009580, 0.006121, 0.004619, 0.001999, -0.001550, -0.002920, -0.003061, 0.002306, 0.010865, 0.021046, 0.025303, 0.025454, 0.026497, 0.025266, 0.025435, 0.021549, 0.016613, 0.012761, 0.015595
|
||||
#*# -0.018344, -0.015904, -0.015984, -0.014773, -0.011019, -0.008011, -0.003822, -0.003839, -0.001582, 0.005968, 0.011839, 0.014291, 0.008873, 0.003278, 0.003240, -0.000129, 0.000031, -0.004615, 0.004193, 0.012619, 0.025125, 0.029778, 0.028265, 0.030261, 0.029398, 0.031480, 0.023715, 0.021064, 0.017546, 0.022917
|
||||
#*# -0.014369, -0.012081, -0.012624, -0.011872, -0.009220, -0.007906, -0.005120, -0.004643, -0.000389, 0.006338, 0.011438, 0.013043, 0.009554, 0.006548, 0.003286, -0.000269, -0.001595, 0.000266, 0.006079, 0.013483, 0.025290, 0.032163, 0.033635, 0.032074, 0.030403, 0.030329, 0.027554, 0.022068, 0.018749, 0.022475
|
||||
#*# -0.012035, -0.009019, -0.011018, -0.011065, -0.007828, -0.006997, -0.004302, -0.003788, 0.000919, 0.007621, 0.013442, 0.017367, 0.011846, 0.012498, 0.007135, 0.004068, 0.002002, 0.005426, 0.011303, 0.019782, 0.030688, 0.036689, 0.035319, 0.034883, 0.034403, 0.031412, 0.029044, 0.023456, 0.020325, 0.023433
|
||||
#*# -0.004839, -0.004396, -0.005090, -0.004725, -0.001368, -0.003840, -0.002306, -0.001376, 0.003799, 0.008782, 0.014308, 0.016840, 0.015013, 0.011839, 0.010347, 0.009470, 0.007995, 0.011020, 0.017949, 0.026647, 0.036527, 0.042245, 0.044427, 0.040763, 0.036771, 0.034253, 0.031374, 0.027671, 0.025724, 0.027465
|
||||
#*# -0.004316, -0.007808, -0.003772, -0.003545, -0.001422, -0.003675, -0.003008, 0.001867, 0.005789, 0.014644, 0.014183, 0.019450, 0.015768, 0.014619, 0.010976, 0.003636, 0.008206, 0.011395, 0.023711, 0.028960, 0.035635, 0.044192, 0.044450, 0.045726, 0.035636, 0.036454, 0.033708, 0.031450, 0.026670, 0.025071
|
||||
#*# -0.008655, -0.005094, -0.005526, -0.003811, -0.003159, -0.003024, -0.003019, -0.000913, 0.003236, 0.010866, 0.017172, 0.016991, 0.012689, 0.009886, 0.008474, 0.005435, 0.005597, 0.008538, 0.018085, 0.028353, 0.037675, 0.041500, 0.041444, 0.037521, 0.035253, 0.035890, 0.036491, 0.032092, 0.029045, 0.029010
|
||||
#*# -0.007356, -0.005498, -0.005814, -0.003044, -0.000431, -0.001744, -0.001574, 0.001773, 0.006326, 0.013551, 0.016679, 0.017341, 0.014874, 0.009867, 0.006378, 0.004765, 0.005251, 0.010967, 0.023185, 0.029603, 0.037213, 0.043252, 0.043208, 0.043564, 0.039273, 0.041440, 0.040003, 0.036057, 0.030071, 0.029832
|
||||
#*# 0.000956, -0.001811, -0.002505, -0.000961, 0.000864, 0.002232, 0.003235, 0.004919, 0.009595, 0.014817, 0.018849, 0.018165, 0.015145, 0.010705, 0.006982, 0.006331, 0.008054, 0.014141, 0.023797, 0.035083, 0.042039, 0.046588, 0.046806, 0.045336, 0.045880, 0.048419, 0.047026, 0.039931, 0.034784, 0.035994
|
||||
#*# 0.003919, 0.006339, -0.000740, -0.001127, 0.001755, 0.001550, 0.003224, 0.005581, 0.009724, 0.012775, 0.018133, 0.017328, 0.013418, 0.010353, 0.007946, 0.006506, 0.008699, 0.014233, 0.021644, 0.033576, 0.044000, 0.045753, 0.047358, 0.046146, 0.046359, 0.047555, 0.045530, 0.039212, 0.036007, 0.034809
|
||||
#*# 0.003141, -0.003151, -0.002952, -0.003129, -0.001673, -0.002364, -0.001570, -0.000185, 0.003673, 0.009292, 0.012555, 0.012521, 0.009632, 0.006946, 0.003490, 0.001724, 0.004319, 0.009574, 0.017502, 0.027046, 0.035213, 0.041406, 0.043813, 0.042409, 0.039537, 0.040232, 0.038264, 0.031443, 0.027606, 0.027877
|
||||
#*# 0.007174, 0.003155, -0.004711, -0.006206, -0.001475, -0.005241, -0.005538, -0.005987, 0.001112, 0.007883, 0.010181, 0.010734, 0.007989, 0.005819, 0.005598, 0.001476, 0.002641, 0.004885, 0.014170, 0.021898, 0.029614, 0.034450, 0.037670, 0.038995, 0.038445, 0.039490, 0.035213, 0.028461, 0.018946, 0.021209
|
||||
#*# 0.006407, 0.001200, -0.002115, -0.003049, -0.004046, -0.005363, -0.004203, -0.001876, 0.001219, 0.005891, 0.010092, 0.012303, 0.008808, 0.005132, 0.003656, 0.002952, 0.002493, 0.005937, 0.011178, 0.019183, 0.028263, 0.035378, 0.037432, 0.037660, 0.038214, 0.038017, 0.034160, 0.026535, 0.022779, 0.024688
|
||||
#*# 0.009883, 0.004892, 0.002338, 0.000764, -0.001461, -0.001838, -0.001564, -0.000265, 0.003133, 0.006444, 0.010819, 0.012607, 0.010269, 0.006413, 0.004381, 0.004025, 0.004001, 0.007085, 0.014154, 0.020939, 0.026734, 0.034161, 0.037692, 0.038189, 0.037848, 0.039113, 0.034547, 0.027312, 0.023446, 0.026240
|
||||
#*# x_count = 30
|
||||
#*# y_count = 30
|
||||
#*# mesh_x_pps = 2
|
||||
#*# mesh_y_pps = 2
|
||||
#*# algo = bicubic
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 30.0
|
||||
#*# max_x = 310.0
|
||||
#*# min_y = 30.0
|
||||
#*# max_y = 310.0
|
||||
|
|
|
|||
Loading…
Add table
Reference in a new issue