From 279686dcf5569a7767c8738247e892af7fe26794 Mon Sep 17 00:00:00 2001 From: Martyn Date: Wed, 14 Aug 2024 16:09:11 +0100 Subject: [PATCH] Changes from 2024-08-14 --- printer.cfg | 54 ++++++++++++++++++++++++++++++++++++----------------- 1 file changed, 37 insertions(+), 17 deletions(-) diff --git a/printer.cfg b/printer.cfg index ca73ef7..481a46c 100644 --- a/printer.cfg +++ b/printer.cfg @@ -27,18 +27,17 @@ canbus_uuid: 970febd72165 [include ebb36.cfg] [include klicky-probe.cfg] [include klicky-quad-gantry-level.cfg] -[include klicky_z_calibration.cfg] [include fluidd.cfg] [include stealthburner_leds.cfg] [include bedfans.cfg] [include martyn_macros.cfg] - +[include shaketune.cfg] [printer] kinematics: corexy -max_velocity: 300 -max_accel: 3000 #Max 4000 +max_velocity: 700 +max_accel: 3300 #Max 4000 max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V max_z_accel: 350 square_corner_velocity: 5.0 @@ -61,7 +60,7 @@ endstop_pin: PG6 position_min: 0 position_endstop: 345 position_max: 345 -homing_speed: 25 #Max 100 +homing_speed: 50 #Max 100 homing_retract_dist: 5 homing_positive_dir: true @@ -87,7 +86,7 @@ endstop_pin: PG9 position_min: 0 position_endstop: 350 position_max: 350 -homing_speed: 25 #Max 100 +homing_speed: 50 #Max 100 homing_retract_dist: 5 homing_positive_dir: true @@ -113,7 +112,8 @@ enable_pin: !PG5 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 -endstop_pin: PG10 +#endstop_pin: PG10 +endstop_pin:probe:z_virtual_endstop ## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) ## (+) value = endstop above Z0, (-) value = endstop below ## Increasing position_endstop brings nozzle closer to the bed @@ -121,7 +121,7 @@ endstop_pin: PG10 #position_endstop: -0.5 position_max: 310 position_min: -5 -homing_speed: 8 +homing_speed: 15 second_homing_speed: 3 homing_retract_dist: 3 @@ -417,33 +417,53 @@ gcode: RESTORE_GCODE_STATE NAME=STATE_PRINT_END +[probe] +pin: ebb36:PB8 +x_offset: 0 +y_offset: 19.75 +z_offset: 5.930 +# below is default, trying -0.365 measured, if +0.365, it's 6.785 +# z_offset: 6.42 +speed: 5 +samples: 3 +samples_result: median +sample_retract_dist: 2.0 +samples_tolerance: 0.01 +samples_tolerance_retries: 3 + [bed_mesh] speed: 120 horizontal_move_z: 10 mesh_min: 35, 35 mesh_max: 320, 320 zero_reference_position: 175, 175 -probe_count: 7, 7 +#probe_count: 5, 5 mesh_pps: 3, 3 algorithm: bicubic bicubic_tension: 0.2 +probe_count: 7, 7 + +[input_shaper] +shaper_freq_x: 91.4 +shaper_freq_y: 70.0 +shaper_type: 3hump_ei #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [stepper_z] -#*# position_endstop = -0.765 +#*# position_endstop = -0.645 #*# #*# [bed_mesh default] #*# version = 1 #*# points = -#*# 0.054626, 0.052126, 0.077126, 0.073376, 0.084626, 0.057126, 0.070876 -#*# 0.017126, 0.007126, 0.017126, 0.024626, 0.040876, 0.032126, 0.062126 -#*# -0.001624, -0.004124, -0.011624, -0.026624, -0.001624, 0.007126, 0.027126 -#*# -0.019124, -0.032874, -0.029124, 0.002126, -0.000374, -0.014124, 0.028376 -#*# -0.007874, -0.009124, -0.015374, -0.016624, 0.030876, 0.024626, 0.050876 -#*# 0.043376, 0.037126, 0.023376, 0.027126, 0.045876, 0.085876, 0.043376 -#*# 0.087126, 0.097126, 0.119626, 0.129626, 0.172126, 0.114626, 0.079626 +#*# 0.038148, 0.031898, 0.059398, 0.053148, 0.066898, 0.040648, 0.053148 +#*# 0.014398, 0.005648, 0.014398, 0.023148, 0.035648, 0.020648, 0.036898 +#*# -0.005602, -0.015602, -0.006852, -0.025602, -0.004352, 0.000648, 0.020648 +#*# -0.028102, -0.036852, -0.025602, 0.001898, -0.004352, -0.021852, 0.020648 +#*# -0.013102, -0.014352, -0.015602, -0.016852, 0.028148, 0.015648, 0.040648 +#*# 0.031898, 0.030648, 0.016898, 0.021898, 0.040648, 0.074398, 0.035648 +#*# 0.060648, 0.080648, 0.108148, 0.120648, 0.158148, 0.106898, 0.066898 #*# x_count = 7 #*# y_count = 7 #*# mesh_x_pps = 3